wrongway
Pro
Posts: 1078
|
posted September 09, 2010 05:12 AM
how much gain in power did Jim predict with that setup ?
|
Shane661

Needs a life
Posts: 11494
|
posted September 09, 2010 05:19 AM
Edited By: Shane661 on 9 Sep 2010 13:20
Based on what we talked about, I am hoping to see 12-14 hp between the head and TB's. That would put me very near 200 hp SAE. That is my best conservative guess, based on what Jim and I discussed.
My head has the stage 2 port, a good valve job, and a decent mill for a good compression increase.
I can't recall the specifics of how we broke down the power gains; I'm sure Jim can add more to this.
Shane
|
Obba

Expert Class
Posts: 455
|
posted September 10, 2010 12:53 AM
Edited By: Obba on 10 Sep 2010 09:00
@1bad,
I know you can be 'controversal' in your posts and some respected members have said you're an ok guy -in the flesh.
But really, do you think it's constructive to this forum for your constant 'It's me! Look! It's me!", posts?
The joke/humor - for me, anyway - has worn off.
The initial links to the OP question, was in bad taste.
If you know more - in real life - than what you portray as just a bit of banter here and there with a bit of 'real time' experience thrown in, then why don't you just tone down a bit and make the casual reader look forward to your replies with a belief that they will reading something proactive and helpful?
And whilst i am it: Shane, you do a great job and your postings have been a dream for many - gotta be - thousands of Z14 and other bike owners. But as other members have said, maybe you should just let others have a bit of leeway in what they think is right.
Sure, chucking money in and having the gear - and the time - to test/measure/calibrate and 'weigh' [pun intended], all the options must be a godsend to us all. And it's a massive helpful addition that you are able to do this and on other forums - plus take the time to post constantly updated pictures and describe your failings and success's [spell?].
Anyway. Glad to see the top page of posts getitng back to the normal ZX14 topics.
Obba
PS: From Aussie land. Hope your 9/11 goes ok for you. Stay strong.
|
smokinZX14

Needs a life
Posts: 10197
|
posted September 10, 2010 07:19 AM
quote: Based on what we talked about, I am hoping to see 12-14 hp between the head and TB's. That would put me very near 200 hp SAE. That is my best conservative guess, based on what Jim and I discussed.
My head has the stage 2 port, a good valve job, and a decent mill for a good compression increase.
I can't recall the specifics of how we broke down the power gains; I'm sure Jim can add more to this.
Shane
12 to 14 easy .. Jesses bike with just intake bowl work and 20 off the head made 13 HP .. You are going full port with 30 off the head .. Unless you install the head upside down it going to make great power .. I would try 105in 105ex on the cam timing and see what the PV clearance is, if to close you may have to go 107in 104ex to get the PV if needed ..
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
Shane661

Needs a life
Posts: 11494
|
posted September 10, 2010 07:28 AM
Edited By: Shane661 on 10 Sep 2010 15:28
quote: 12 to 14 easy .. Jesses bike with just intake bowl work and 20 off the head made 13 HP .. You are going full port with 30 off the head .. Unless you install the head upside down it going to make great power .. I would try 105in 105ex on the cam timing and see what the PV clearance is, if to close you may have to go 107in 104ex to get the PV if needed ..
That will be great if it makes near 15 hp with the bigger throttle bodies.15 hp is a big gain with stock cams and pistons, imo. We figured we may have to spread the lobe centers a little for clearance, but it shouldn't be a big deal. The cylinder head arrived yesterday, and it looks pretty darn good.
Shane
|
oilfieldtrash
Zone Head
Kawasaki enthusiast
Posts: 506
|
posted September 10, 2010 07:41 AM
Shane you gonna update the build thread with your new head? Sounds interesting.
Are you gonna be pissed if the new zx10 makes 190hp and weighs 430lbs stock?
____________
'09 zx6r lime green bone stock
'07 white S.E. ZX-14 sold
|
Shane661

Needs a life
Posts: 11494
|
posted September 10, 2010 07:44 AM
I'll be posting pictures of the head soon, maybe this weekend.
I'd love to see the new 10R have those specs.
|
Shane661

Needs a life
Posts: 11494
|
posted September 10, 2010 03:20 PM
Too tired to start a new thread tonight, but here is a sample of Jim's port work:

Anyway, I'll try to get more details and pictures up later this weekend.
Shane
|
wrongway
Pro
Posts: 1078
|
posted September 10, 2010 05:40 PM
quote: Too tired to start a new thread tonight, but here is a sample of Jim's port work:

Anyway, I'll try to get more details and pictures up later this weekend.
Shane
is that hand ported ?? doesnt look like a cnc did it ....
Roy
|
KZScott

Needs a life
high on speed
Posts: 7235
|
posted September 10, 2010 05:43 PM
Edited By: KZScott on 11 Sep 2010 01:44
quote:
is that hand ported ?? doesnt look like a cnc did it ....
Roy
why doent it look like cnc???
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos
|
wrongway
Pro
Posts: 1078
|
posted September 10, 2010 06:07 PM
quote:
quote:
is that hand ported ?? doesnt look like a cnc did it ....
Roy
why doent it look like cnc???
the CNC ported heads I have are much smoother and you can see the cutter path .
Roy
|
smokinZX14

Needs a life
Posts: 10197
|
posted September 10, 2010 09:31 PM
I guess Jim could have run a flapper in the ports wheel after the CNC work ?
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
ZX14Mike
Zone Head
Posts: 891
|
posted September 10, 2010 10:52 PM
Keep us posted Shane...........I cant wait to hear the results!!
|
Shane661

Needs a life
Posts: 11494
|
posted September 11, 2010 02:56 AM
Edited By: Shane661 on 11 Sep 2010 11:25
quote:
is that hand ported ?? doesnt look like a cnc did it ....
Roy
Definitely not hand ported. It would probably be more obvious if you had the part in your hands. The symmetry and precision of the cuts is pretty cool. I couldn't imagine doing that kind of precise work by hand alone in such a tiny port...
I imagine that doing it by hand must be somewhat painstaking work. I mean, in order to get a precise taper would take a lot of trial and error, port molds, etc. Of course, basic head work doesn't really involve changing the shape of the port. Do you have any pictures of what you have done, Roy?
Shane
|
Y2KZX12R

Needs a job
CompetitionCNC.com
Posts: 3762
|
posted September 11, 2010 04:29 AM
quote: Shane, 12 to 14 easy .. Jesses bike with just intake bowl work and 20 off the head made 13 HP .. You are going full port with 30 off the head .. Unless you install the head upside down it going to make great power .. I would try 105in 105ex on the cam timing and see what the PV clearance is, if to close you may have to go 107in 104ex to get the PV if needed ..
Lee I was wondering how you guys made out with jesses bike. I hadnt heard anything.
So is he mid 190's with the super sport head?
____________
Y2KZX12R
CompetitionCNC.com
|
Y2KZX12R

Needs a job
CompetitionCNC.com
Posts: 3762
|
posted September 11, 2010 04:41 AM
Roy I think what you are seeing is where we blended in the rubber manifolds by hand.
These pictures dot really show the cnc cutter marks very well.
If you compare our cnc work to any other that I have seen you will notice one thing first off. We use a .020" step over in a spiral cut. Every other cnc head porter that I know of does at least a .030" but more often a .040 or larger step over.
With our .020" step over and the 3/8" cutter ball dia. the scallop height is something like .0002" or so. basically a scotch pad will remove any sign of machining.
We don't "polish the port by hand after because you don't need to with such a smooth finish and people want to see the cnc cutter marks for some reason.
On many of the race heads we do for some "other" shops we use a flapper in the ports after to remove any cnc marks and smooth the port 100%. But we don't do that as a rule unless its requested. And its really just a cosmetic thing.
In all actuality there is nothing you can see with your eyes that will tell you how good or bad a porting job is on one of these heads other than if there was a crappy transition from the port to the valve seat.
____________
Y2KZX12R
CompetitionCNC.com
|
smokinZX14

Needs a life
Posts: 10197
|
posted September 11, 2010 04:53 AM
quote:
quote: Shane, 12 to 14 easy .. Jesses bike with just intake bowl work and 20 off the head made 13 HP .. You are going full port with 30 off the head .. Unless you install the head upside down it going to make great power .. I would try 105in 105ex on the cam timing and see what the PV clearance is, if to close you may have to go 107in 104ex to get the PV if needed ..
Lee I was wondering how you guys made out with jesses bike. I hadnt heard anything.
So is he mid 190's with the super sport head?
Jim Jesse gave up racing .. He sold the SS head to somebody ..Now he is selling the bike .... I was pretty upset that i didn't get to test the head ...
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
KZScott

Needs a life
high on speed
Posts: 7235
|
posted September 11, 2010 06:28 AM
Roy, this is Jims cnc porting on my 12 head

i need to get this head repaired after my blow up.... have some cracked guides and bent valves. might be going your way soon Jim
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos
|
wrongway
Pro
Posts: 1078
|
posted September 11, 2010 06:51 AM
shanes picture just doesnt show the cutter marks at all. I had to go back and really look hard to find a small area where they were visible.
Roy
|
Shane661

Needs a life
Posts: 11494
|
posted September 11, 2010 06:53 AM
Edited By: Shane661 on 11 Sep 2010 14:58
quote: shanes picture just doesnt show the cutter marks at all. I had to go back and really look hard to find a small area where they were visible.
Roy
I have a very good extreme close-up of the cutter marks, but I was just too tired to post all the pics last night. Probably will get time tomorrow. That picture above is also reduced to about 25% of it's original resolution.
|
Obba

Expert Class
Posts: 455
|
posted September 11, 2010 01:06 PM
Some interesting info on why having a polished port (on the intake), is not be needed - but might be for the Exhaust port.
From Wiki:
The "Porting and Polishing" myth
It is popularly held that enlarging the ports to the maximum possible size and applying a mirror finish is what porting is. However that is not so. Some ports may be enlarged to their maximum possible size (in keeping with the highest level of aerodynamic efficiency) but those engines are highly developed very high speed units where the actual size of the ports has become a restriction. Larger ports flow more fuel/air at higher RPM's but sacrifice torque at lower RPM's due to lower fuel/air velocity.
A mirror finish of the port does not provide the increase that intuition suggests. In fact, within intake systems, the surface is usually deliberately textured to a degree of uniform roughness to encourage fuel deposited on the port walls to evaporate quickly.
A rough surface on selected areas of the port may also alter flow by energizing the boundary layer, which can alter the flow path noticeably, possibly increasing flow. This is similar to what the dimples on a golf ball do.
Flow bench testing shows that the difference between a mirror finished intake port and a rough textured port is typically less than 1%. The difference between a smooth to the touch port and an optically mirrored surface is not measurable by ordinary means.
Exhaust ports may be smooth finished because of the dry gas flow and in the interest of minimizing exhaust by-product build-up. A 300 - 400 Grit finish followed by a light buff is generally accepted to be representative of a near optimal finish for exhaust gas ports.
The reason that polished ports are not advantageous from a flow standpoint is that at the interface between the metal wall and the air, the air speed is ZERO (see boundary layer and laminar flow). This is due to the wetting action of the air and indeed all fluids.
The first layer of molecules adheres to the wall and does not move significantly. The rest of the flow field must shear past, which develops a velocity profile (or gradient) across the duct. For surface roughness to impact flow appreciably, the high spots must be high enough to protrude into the faster moving air toward the center. Only a very rough surface does this.
|
Shane661

Needs a life
Posts: 11494
|
posted September 11, 2010 03:10 PM
Edited By: Shane661 on 11 Sep 2010 23:40
Some close-ups of the Competition CNC porting:


These pictures better illustrate the work of the cnc cutter.
|
kawa74

Expert Class
Posts: 226
|
posted September 11, 2010 04:08 PM
Hi Roy, Think AIR Quality, No Turbulamce , Forget about what you see or what you feel with your finger, its what the [ AIR SEES ] , you need PROBES, A Straight for Velocity and U shaped to find turbulance, can get .020 tubing at hobby shop , RC airplane struts, these Probes will tell you were to Cut or Fill. Valve Seats are most important Area , 45, 50, 55 seat, with a 60 and 70 undercut .ROUGH ports are best for Fuel Atomizing. no Polish ??
This is the best artitcle on porting I have seen in 35 years of porting, written by Jim MacFarland , he worked with Smoke Yunick for 40 years. Read it 2 or 3 times ?? Also sometimes you have to FILL, not make bigger??
http://www.circletrack.com/enginetech/ctrp_0806_mc_part_5/index.html
____________
"I have never met a man so Ignorant that I coun't Learn from him"..."Galileo"
|
KZScott

Needs a life
high on speed
Posts: 7235
|
posted September 11, 2010 04:54 PM
Jim does some epoxy ports too. building it up where it needs it, then making it the right shape with the cnc
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos
|
Lucky14

Pro
Posts: 1439
|
posted September 11, 2010 07:36 PM
quote:
This is the best artitcle on porting I have seen in 35 years of porting, written by Jim MacFarland , he worked with Smoke Yunick for 40 years. Read it 2 or 3 times ?? Also sometimes you have to FILL, not make bigger??
http://www.circletrack.com/enginetech/ctrp_0806_mc_part_5/index.html
Gotta make it easy on people here.
http://www.circletrack.com/enginetech/ctrp_0806_mc_part_5/index.html
Good stuff! However, I would bet that most won't make it past Page 1 ...................
____________
You only need two tools: WD-40 and Duct Tape.
If it doesn't move and should, use the WD-40.
If it shouldn't move and does, use the duct tape.
|
|
|