pazx14rider

Zone Head
Posts: 953
|
posted June 29, 2009 03:47 PM
So Lee all you did to gain the 4hp down low was pull the flies on your 09? Did you put your Brocks pipe on your 09 yet?
|
smokinZX14

Needs a life
Posts: 10197
|
posted June 29, 2009 03:47 PM
quote: Very close to what mine showed with the shortmeg and street map:

How much difference is there between Dynojet units? This was done on a 200...
Shane
Shane this is also a 200 ... The difference in power was most likely the air ... But that is very close for sure ..
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
smokinZX14

Needs a life
Posts: 10197
|
posted June 29, 2009 03:53 PM
quote: So Lee all you did to gain the 4hp down low was pull the flies on your 09? Did you put your Brocks pipe on your 09 yet?
Yes this is my 09 ... Flys pulled ... Brocks street meg is the one off my 06 .. It's been on the 09 for a good while now .. All i did was change maps and pull the flys ...
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
pazx14rider

Zone Head
Posts: 953
|
posted June 29, 2009 05:47 PM
Lee Id like to see a pull with the Maxton map and see if theres much difference
|
smokinZX14

Needs a life
Posts: 10197
|
posted June 29, 2009 06:02 PM
quote: Lee Id like to see a pull with the Maxton map and see if theres much difference
I would do that but i don't have a Maxton map for the 08 09 , I still have the 06 Maxton Map for the P/C3.. My 09 uses the PCV ... I may be able to to make one, the maxtom map is just the track map with some fuel added to the top of the map.. I will look into it and see..
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
smokinZX14

Needs a life
Posts: 10197
|
posted June 29, 2009 06:29 PM
Something i didn't think about is my 09 only has 500 miles on it .. Brock said his 08 started making better Dyno numbers after putting more miles on it than mine .. If i remember right he said it really picked up HP numbers after 1000 miles..Brock felt the 08 09 zx14 motor was tighter and took longer break in than his 06 07 zx14s ..
I remember tonytooths zx14 dyno'd in the mid 170s and on the same dyno after 1000+ miles it put up 181 on the same dyno ..
We are going to Dyno Tommy 06 zx14 Tuesday .. His bike is set up the same way my 06 zx14 was ...Tommys bike has a lot of miles on it , more than my 06 had ... I'll post up the numbers Tuesday night ..
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
AcadianaZX

Advertiser
Posts: 530
|
posted June 29, 2009 11:26 PM
Smokin, The Boss will send it your way. Thanks
James
|
SteddyTeddy
Pro
Posts: 1664
|
posted June 30, 2009 03:23 AM
quote: Something i didn't think about is my 09 only has 500 miles on it .. Brock said his 08 started making better Dyno numbers after putting more miles on it than mine .. If i remember right he said it really picked up HP numbers after 1000 miles..Brock felt the 08 09 zx14 motor was tighter and took longer break in than his 06 07 zx14s ..
I remember tonytooths zx14 dyno'd in the mid 170s and on the same dyno after 1000+ miles it put up 181 on the same dyno ..
We are going to Dyno Tommy 06 zx14 Tuesday .. His bike is set up the same way my 06 zx14 was ...Tommys bike has a lot of miles on it , more than my 06 had ... I'll post up the numbers Tuesday night ..
Take that bike out for a couple good long rides.
|
AcadianaZX

Advertiser
Posts: 530
|
posted June 30, 2009 05:42 AM
Smokin, hopefully you see the oil Friday or Monday. Maybe sooner, I believe there's a distribution center near you.
Have you over came the clutch grab? The Dominator Racing 5w20 may put you back into that little bit of slip on the clutch.
Was your dyno done on the bike with the Amsoil? I hope to see a better gain on your dyno results with the 5w20. If you like it, let my boss know. She would like to here from you. That would help me out if you know what I mean (haha). Thanks a bunch
James
|
AcadianaZX

Advertiser
Posts: 530
|
posted June 30, 2009 05:48 AM
quote: Looks like my ZRX will be the dyno king so far. LOL
Hang on SteddyTeddy were working on something. LOL
|
SteddyTeddy
Pro
Posts: 1664
|
posted June 30, 2009 06:01 AM
That reminds me, I need to give your wife a call here soon and order up some oil.
I'm not going to be able to match that TQ, but after a little tuning and a couple more upgrades I don't think he'll match my HP #'s with out breaking into the motor. 2 can play the thin oil game. LOL
|
bigdtd

Needs a job
Interceptors
Posts: 4209
|
posted June 30, 2009 06:32 AM
i will have to bring mine down and see if its a wednesday bike lol
____________
2006 Black ZX-14,6 inches over,16/42, flies out,BMC Street Filter,Brock's Street Meg,Brock's Radial Mount Strap,PClll with Race map,Dynojet LCD w/Techmount, ZX-14 fender eliminator,Pilot Power2CTs,Speedohealer,Pazzo Levers,Cox Radiator Guard, Garmin Nuvi 265WT
|
AcadianaZX

Advertiser
Posts: 530
|
posted June 30, 2009 06:39 AM
quote: That reminds me, I need to give your wife a call here soon and order up some oil.
I'm not going to be able to match that TQ, but after a little tuning and a couple more upgrades I don't think he'll match my HP #'s with out breaking into the motor. 2 can play the thin oil game. LOL
Looking forward to its. Call anytime.
|
smokinZX14

Needs a life
Posts: 10197
|
posted June 30, 2009 06:45 AM
quote:
quote: Something i didn't think about is my 09 only has 500 miles on it .. Brock said his 08 started making better Dyno numbers after putting more miles on it than mine .. If i remember right he said it really picked up HP numbers after 1000 miles..Brock felt the 08 09 zx14 motor was tighter and took longer break in than his 06 07 zx14s ..
I remember tonytooths zx14 dyno'd in the mid 170s and on the same dyno after 1000+ miles it put up 181 on the same dyno ..
We are going to Dyno Tommy 06 zx14 Tuesday .. His bike is set up the same way my 06 zx14 was ...Tommys bike has a lot of miles on it , more than my 06 had ... I'll post up the numbers Tuesday night ..
Take that bike out for a couple good long rides.
After the 4th st bust and last Sat night Bust on Gandy no way i'm I riding on the street ..Cops are out in force to bust any sport bike rider ..You are safe if you are drunk and riding a Hogly Davidson ..
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
bigdtd

Needs a job
Interceptors
Posts: 4209
|
posted June 30, 2009 06:47 AM
Edited By: bigdtd on 30 Jun 2009 14:56
they had one on gandy too? that sucks. back to the thread does the dyno flat spot a tire badly? would a new or old tire make more ponies? i think the reason people say the shinko makes less power is because of how much it weighs with all the extra rubber. that extra spinning mass would have to cost a few ponies.
____________
2006 Black ZX-14,6 inches over,16/42, flies out,BMC Street Filter,Brock's Street Meg,Brock's Radial Mount Strap,PClll with Race map,Dynojet LCD w/Techmount, ZX-14 fender eliminator,Pilot Power2CTs,Speedohealer,Pazzo Levers,Cox Radiator Guard, Garmin Nuvi 265WT
|
smokinZX14

Needs a life
Posts: 10197
|
posted June 30, 2009 06:52 AM
quote: Smokin, hopefully you see the oil Friday or Monday. Maybe sooner, I believe there's a distribution center near you.
Have you over came the clutch grab? The Dominator Racing 5w20 may put you back into that little bit of slip on the clutch.
Was your dyno done on the bike with the Amsoil? I hope to see a better gain on your dyno results with the 5w20. If you like it, let my boss know. She would like to here from you. That would help me out if you know what I mean (haha). Thanks a bunch
James
Thanks James ...James i have not been back to the track since my last post .. We are going to go Weds if we don't get rained out ... All four Dyno runs were done on the Amsoil you sent me ... It will be a while before it's do to be changed , don't want to waste good oil and change it before it's time .. But when i do change it i will get some dyno number posted .. Thanks again ..
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
smokinZX14

Needs a life
Posts: 10197
|
posted June 30, 2009 06:55 AM
quote: they had one on gandy too?
Yup .. They closed off both sides and blocked everybody in just like 4th st ... My guess is CC is next ....
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
bigdtd

Needs a job
Interceptors
Posts: 4209
|
posted June 30, 2009 07:01 AM
Edited By: bigdtd on 30 Jun 2009 15:01
quote: they had one on gandy too? that sucks. back to the thread does the dyno flat spot a tire badly? would a new or old tire make more ponies? i think the reason people say the shinko makes less power is because of how much it weighs with all the extra rubber. that extra spinning mass would have to cost a few ponies.
i wonder if they are going to target gathering spots next. i quoted the above post to get your ideas on dynos and tires..
____________
2006 Black ZX-14,6 inches over,16/42, flies out,BMC Street Filter,Brock's Street Meg,Brock's Radial Mount Strap,PClll with Race map,Dynojet LCD w/Techmount, ZX-14 fender eliminator,Pilot Power2CTs,Speedohealer,Pazzo Levers,Cox Radiator Guard, Garmin Nuvi 265WT
|
SteddyTeddy
Pro
Posts: 1664
|
posted June 30, 2009 07:02 AM
Edited By: SteddyTeddy on 30 Jun 2009 15:03
Well quit hanging out with the F'en street racers and just take the bike for a ride. Don't act stupid or hang around others acting stupid and the cops will leave you alone. Not the best time of the year to be riding down here though. Give me that air conditioning!!!!
|
smokinZX14

Needs a life
Posts: 10197
|
posted June 30, 2009 07:11 AM
quote: they had one on gandy too? that sucks. back to the thread does the dyno flat spot a tire badly? would a new or old tire make more ponies? i think the reason people say the shinko makes less power is because of how much it weighs with all the extra rubber. that extra spinning mass would have to cost a few ponies.
The dyno did no damage to my shinko ... But a true street tire should act much better ... Dave i truly don't have an answer to your question ( yet ) ...I'm NO pro on this dyno thing , Unlike some guys that buy a dyno and the next day they are the best tunners in the world ...I hope to learn along with you guys and clear up some of the myths about dynos ..
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
smokinZX14

Needs a life
Posts: 10197
|
posted June 30, 2009 07:14 AM
quote: Well quit hanging out with the F'en street racers and just take the bike for a ride. Don't act stupid or hang around others acting stupid and the cops will leave you alone. Not the best time of the year to be riding down here though. Give me that air conditioning!!!!
So Teddy does that mean i can't hang out with you ? lol .....
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
SteddyTeddy
Pro
Posts: 1664
|
posted June 30, 2009 07:34 AM
I'll keep ya out of trouble. LOL
|
Sticks_n_Stones

Needs a job
Posts: 3930
|
posted June 30, 2009 07:44 AM
quote: I'll keep ya out of trouble. LOL
Thats what she said!
How about a timing advance dyno run? Do you have a advancer handy? I can mail you mine, I've had it in n out a few times, trying to 'seat of the pants' decide if I lose topend with 3 more degrees advance like I've heard numerous guys here state. It definitely gives it crisper throttle response and more low end power though.
____________
'06 zx14
Muzzy M10/M14
PCIII w/ Muzzy map
Flies out K&N in!
bits n pieces...
|
smokinZX14

Needs a life
Posts: 10197
|
posted July 01, 2009 02:51 PM
Edited By: smokinZX14 on 1 Jul 2009 22:56
Just got done running Tommys 06 red zx14 on the Dyno .. 3 pulls and the best was ( SAE ) 175.15 and 100 foot pounds of TQ.. Brocks Smeg, Track map and 87 pump gas ..AFR was just a bit fat at 6000 but was fine on the top end and bottom end ...
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
smokinZX14

Needs a life
Posts: 10197
|
posted July 01, 2009 02:54 PM
quote:
quote: I'll keep ya out of trouble. LOL
Thats what she said!
How about a timing advance dyno run? Do you have a advancer handy? I can mail you mine, I've had it in n out a few times, trying to 'seat of the pants' decide if I lose topend with 3 more degrees advance like I've heard numerous guys here state. It definitely gives it crisper throttle response and more low end power though.
Yes sticks i would like to test one ... If you want to send me one to test that would be fine ...
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
|
|