UGADawg
Novice Class
Posts: 45
|
posted August 18, 2004 03:57 PM
Dynoed today
I have to say I am a bit bummed out. Total stock bike, with 1600 miles and it made 144.8 on the 2nd pull. Dynojet rollers, and 93 degrees temp. What are most people seeing with stock bikes and then how much is slip ons and power commanders and K&Ns worth? I knew some of these magazine #s are a bunch of hogwash but I was hoping for 150ish stock. What are you guys seeing?
|
SP8

Novice Class
Posts: 72
|
posted August 18, 2004 04:20 PM
I haven't dynoed mines yet. I'm waiting until I decide what full system I'm gonna get. Then I'll do back to back runs. Did you ask what the other brands of bikes are getting stock on that dyno. It may be reading low. If so I wouldn't be pissed.
|
frEEk

Administrator
ummm... yeah
Posts: 9660
|
posted August 18, 2004 05:25 PM
do a search on that topic on the board. it has been discussed ad nauseum and the general consensus is that mid 140s to 150 is a pretty normal reading, but it varies hugely depending on the specific dyno and dyno setup.
|
tafb
Expert Class
Posts: 138
|
posted August 18, 2004 09:34 PM
my bike pulled 144 too. i posted a graph.
|
Hells Dark Lord

Needs a life
living life, and loving it.
Posts: 7981
|
posted August 19, 2004 05:48 AM
dam if all i am gonna start out with is 140-145, I am not sure if the goal of 175 that i have set for my bike is gonna be attainable without increasong the bore and stroke...
____________
When in doubt, lean farther and go faster....
|
bovinespongiformencephalo
Pro
variant Kreutzfeldt-Jakob
Posts: 1060
|
posted August 19, 2004 07:23 AM
True that. 30-35 hp is gonna be expensive. Too bad you didn't get one of the mag bikes with 164. Then you'd just be a pipe and some tuning away. I've yet to dyno mine. It's leaving the others for dead, which is good enough.
|
UGADawg
Novice Class
Posts: 45
|
posted August 19, 2004 08:00 AM
Another funny fact was that the bike showed 164 mph on the Dynometer in 4th gear. Should a slip on give these bikes enough power to make 150? K&N filter worth any power?
|
fish_antlers

Administrator
The Truth is Out There
Posts: 21896
|
posted August 19, 2004 08:04 AM
as freek had pointed out.. this has been discussed many many times... do a search on the site for similar threads and you'll see... it's also been shown that a 10R with 3000mi on it makes more HP than a 10R with 1500mi on it.. go figure... this isnt an exact science... but read the other threads...
you shouldnt be disappointed.. you still make the same equivalant HP as a 12R since your bike weighs 130lbs less.
____________
What business is it of yours where I'm from, Friendo?
|
k bryant

Needs a job
Sponsor
Posts: 2911
|
posted August 19, 2004 08:20 AM
At your current reading, a quality Slip-On will put you close to 150hp (+/-).
|
dnwhoop02

Expert Class
Posts: 204
|
posted August 19, 2004 10:19 AM
Edited By: dnwhoop02 on 19 Aug 2004 11:19
quote: At your current reading, a quality Slip-On will put you close to 150hp (+/-).
Hmmm... where can I find such a quality slip-on?
____________
David
'04 ZX-10R
'00 SV650
|
k bryant

Needs a job
Sponsor
Posts: 2911
|
posted August 19, 2004 10:23 AM
Well..... I can think of a few places in particular......
|
fish_antlers

Administrator
The Truth is Out There
Posts: 21896
|
posted August 19, 2004 10:44 AM
http://midas.com/ ?
____________
What business is it of yours where I'm from, Friendo?
|
600champ
Parking Attendant
Posts: 5
|
posted August 19, 2004 01:45 PM
I dynoed mine and on the same dyno that my 03 GSXR1000 stock made 149.7 my ZX10 made 159. Another ZX10 that belongs to a friend of mine made 158 but then a different ZX10 pulled only 150. With a Sato slip on mine made 163 with no map. I just installed my full Arata today and am going to see how it does.
|
dannygzx10r
Parking Attendant
Posts: 2
|
posted August 19, 2004 01:48 PM
hey guys, dont feel bad, it could be the dyno machine.....my ZX10R dynoed at 158 hp with a pc3r and muzzy slip on. the dyno machine was 3 years old.....also it could be the type of rear tire....I wear a michelin pilot sport.....
____________
ZXPLOSION
|
k bryant

Needs a job
Sponsor
Posts: 2911
|
posted August 19, 2004 02:01 PM
It can be many things.... But suffice to say, you have an average good runner. I have seen them "stock" from a low of 140 to a high of over 160.
"Most" are seeing 145 - 150 stock. Your's is an excellent runner and will get stronger with more miles. Enjoy.
|
SP8

Novice Class
Posts: 72
|
posted August 19, 2004 05:04 PM
quote: I dynoed mine and on the same dyno that my 03 GSXR1000 stock made 149.7 my ZX10 made 159. Another ZX10 that belongs to a friend of mine made 158 but then a different ZX10 pulled only 150. With a Sato slip on mine made 163 with no map. I just installed my full Arata today and am going to see how it does.
Please do post your Arata results. I dying to see a owner's results.
|
Deezy
Parking Attendant
Posts: 26
|
posted August 19, 2004 07:30 PM
Stock on a dynojet I got 152.5 (3K miles) After putting on a an Akra Slipon I got 155.5 (90 degree and humid day in Atlanta.
|
UGADawg
Novice Class
Posts: 45
|
posted August 22, 2004 09:09 PM
Deezy, did your bike feel like it picked up much with the Akra Slip on? You ever go up to the Vortex on Thurs nights?
|
extremelean

Pro
Posts: 1651
|
posted August 23, 2004 12:08 PM
YEEEE HAWWWWWW.......whip that horsey!!!...LOL
|
crispin

Expert Class
Posts: 288
|
posted August 24, 2004 04:29 AM
I just installed my PCIII and had my bike tuned on the Dyno.
I have a slip-on (Micron High Mount) and a PCIII.
Stock with 300 miles I pulled a 152.8 now I just pulled a 158.5.
I am pretty happy. I want to get an air cleaner and mabye remove the exhaust valve.
I really want to see 160 on the Dyno.
____________
04 ZX10-R Blue
slightly mod'd...
|
swft

Needs a life
Full throttle!
Posts: One MEEEEEELLION
|
posted August 24, 2004 07:21 AM
bump
|
|
|