TRNorBRN6001
Needs a job
Posts: 2021
|
posted December 04, 2008 01:06 PM
Re-size Con Rods
Anybody know of a good place to send my Arrow Con Rods for resizing. They are running a little small and I would like them a touch bigger so I could run .0020 clearance. Right now I am sitting at about .0010 on the best one and am using the thinest measured bearing out of a set of about 16 halves.
Thanks,
Gary
____________
TFA 200MPH CLUB MEMBER!
  
|
VincentHill
Needs a life
Posts: 6520
|
posted December 04, 2008 01:16 PM
Falicon does most of my crank and rod work for me and the last crank I sent them they sized the journal Exactly the same as it was! Used the same size bearings! I have actually been throiugh their plant in clearwater Fla!
____________
Made History @ Daytona and still one fast old man!!
|
TRNorBRN6001
Needs a job
Posts: 2021
|
posted December 04, 2008 01:41 PM
I don't know if they would do Rods that are not theirs, but I'll give them a call. Thank you much Mr. Hill.
____________
TFA 200MPH CLUB MEMBER!
|
Y2KZX12R
Needs a job
CompetitionCNC.com
Posts: 3762
|
posted December 04, 2008 01:58 PM
Gary,
We have done several sets of busa and zx12r Carillos for Karl and Ryan.
____________
Y2KZX12R
CompetitionCNC.com
|
osti33
Needs a job
Posts: 2973
|
posted December 04, 2008 07:11 PM
quote:
Gary,
We have done several sets of busa and zx12r Carillos for Karl and Ryan.
Yep.
Gary, just send them to Jim. 
|
KZScott
Needs a life
high on speed
Posts: 7235
|
posted December 04, 2008 07:32 PM
I had a local shop resize a couple rods in dads bike that were a bit big(egg shaped). they came back the exact size i asked for(40.002mm)
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos
|
TRNorBRN6001
Needs a job
Posts: 2021
|
posted December 04, 2008 10:23 PM
Dang Jim I think Ryan and Karl like to keep you all to themselves. I thought you just ported.
I'll probably shoot them over to you.
Ryan, when you get a chance shoot me a PM with your #, I think I lost it. I had a couple questions about the PowerCommander LCD Display and multifuntion hub set up.
Thanks you all,
Gary
____________
TFA 200MPH CLUB MEMBER!
|
entropy
Moderator
Posts: 8671
|
posted December 05, 2008 12:03 AM
quote:
Gary,
We have done several sets of busa and zx12r Carillos for Karl and Ryan.
that's a big 10-4!
good work done fast!
____________
This moderator uses moderation in moderation
|
Y2KZX12R
Needs a job
CompetitionCNC.com
Posts: 3762
|
posted December 05, 2008 05:04 AM
Gary, were basically a high end custom engine shop we are setup to do anything. The 5 axis CNC head porting machine was actually just the latest addition to the shops capabilities. Its much easier to list the things we cant do, like grind crankshafts and camshafts.
____________
Y2KZX12R
CompetitionCNC.com
|
entropy
Moderator
Posts: 8671
|
posted December 05, 2008 09:02 AM
quote:
Gary, were basically a high end custom engine shop we are setup to do anything. The 5 axis CNC head porting machine was actually just the latest addition to the shops capabilities. Its much easier to list the things we cant do, like grind crankshafts and camshafts.
You also CAN'T make #8's like Taco Bell, but that's about the list of what you can't do.
GREAT shop, Bill & Jim are GREAT people.
____________
This moderator uses moderation in moderation
|
TRNorBRN6001
Needs a job
Posts: 2021
|
posted December 05, 2008 09:20 AM
They will be sent to Jim this evening or early Sat.
Entropy, keep us posted on the Dyno action on Sat. Say hi to Andy as well.
____________
TFA 200MPH CLUB MEMBER!
|
osti33
Needs a job
Posts: 2973
|
posted December 05, 2008 02:43 PM
 Edited By: osti33 on 5 Dec 2008 22:43
quote:
Dang Jim I think Ryan and Karl like to keep you all to themselves. I thought you just ported.
I'll probably shoot them over to you.
Ryan, when you get a chance shoot me a PM with your #, I think I lost it. I had a couple questions about the PowerCommander LCD Display and multifuntion hub set up.
Thanks you all,
Gary
Gary,
PM sent with number. 
Their isn't to many things they can't do at Jim and Bill's shop.
|
entropy
Moderator
Posts: 8671
|
posted December 05, 2008 03:11 PM
Jim is going to PMI next week, so no action for a bit.
____________
This moderator uses moderation in moderation
|
TRNorBRN6001
Needs a job
Posts: 2021
|
posted December 05, 2008 07:34 PM
Yep, spoke with Jim. No worries. I just can't figure out why Honda did not post actual bearing sizes in their manual. Very Irritating!!!
Entropy, Hope all goes very well at the Dyno on Sat!
Osti, I'll give you a call real soon, nothing important.
____________
TFA 200MPH CLUB MEMBER!
|
Y2KZX12R
Needs a job
CompetitionCNC.com
Posts: 3762
|
posted December 14, 2008 03:11 PM
I stopped by the shop today Gary. The rods are here.
____________
Y2KZX12R
CompetitionCNC.com
|
Y2KZX12R
Needs a job
CompetitionCNC.com
Posts: 3762
|
posted December 18, 2008 04:56 AM
Gary, the rods went out yesterday UPS. You should see them on tues.
____________
Y2KZX12R
CompetitionCNC.com
|
TRNorBRN6001
Needs a job
Posts: 2021
|
posted December 18, 2008 06:29 AM
Thank you much Jim, shot you out the check. You should have it by this Friday or Monday at the latest. Jim, your awesome! Great service, amazingly fast!!!!!!!!!!!
A few more things on the to do list and the old designated LSR motor will start to be put together. Maybe finished by Feb 09
Thank you very, very much,
Gary Dow
____________
TFA 200MPH CLUB MEMBER!
|
VincentHill
Needs a life
Posts: 6520
|
posted December 18, 2008 07:58 AM
Gary, I am like you!! I "KNOW" That what ever Jim does, it is the best possible of anyone, but WHO KNOWS WHAT All he does!!
Again, Y2K, where are you located? VA or CT?
____________
Made History @ Daytona and still one fast old man!!
|
TRNorBRN6001
Needs a job
Posts: 2021
|
posted December 18, 2008 11:51 AM
Sent the money to CT, but it is being re-routed to his secret location in VA! lol
Mr. Hill, hope to see you this summer. Maybe Texas Mile in October?
It's going to be a busy LSR year!
____________
TFA 200MPH CLUB MEMBER!
|
Y2KZX12R
Needs a job
CompetitionCNC.com
Posts: 3762
|
posted December 18, 2008 01:24 PM
Edited By: Y2KZX12R on 18 Dec 2008 21:35
Vince, Were in Oakville CT. CompetitionCNC.com
Basically we build custom engines. But have been known to build :special" 5hp briggs engines for tractor pulling.  Kids like to win also.
Right now I'm waiting for a CNC program to finish running thats cutting "289" with a factory looking font into the valve cover area of a set of 351w heads..... Hey its what the customer wants.
____________
Y2KZX12R
CompetitionCNC.com
|
TRNorBRN6001
Needs a job
Posts: 2021
|
posted December 18, 2008 01:39 PM
Dang Jim, you need an addy in 2WheelTuner or SuperStreetBike mag -------- Bling-Bling!
Just Kidding you
____________
TFA 200MPH CLUB MEMBER!
|
VincentHill
Needs a life
Posts: 6520
|
posted December 18, 2008 02:05 PM
Then it MUST be Flight Leader that lives in Vagina (I mean Virginia )
____________
Made History @ Daytona and still one fast old man!!
|
Y2KZX12R
Needs a job
CompetitionCNC.com
Posts: 3762
|
posted December 19, 2008 04:41 AM
quote:
Dang Jim, you need an addy in 2WheelTuner or SuperStreetBike mag -------- Bling-Bling!
Just Kidding you
Gary, we are working on a project right now that will be in a "major" publication in the spring. A very cool bike making BIG power with lots of trick new products and did I say BIG power?
____________
Y2KZX12R
CompetitionCNC.com
|
TRNorBRN6001
Needs a job
Posts: 2021
|
posted December 19, 2008 06:28 AM
Do tell a little, N/A, Nitrous, Forced Induction?????Busa, 14, 1000, 750, 600, 500, 250?????
____________
TFA 200MPH CLUB MEMBER!
|
2000redrocket
Pro
Posts: 1662
|
posted December 19, 2008 07:40 PM
whatever it is i hope it is a kawasaki
|
|
|
HOME
NEW TOPIC