dougmeyer

Needs a job
moderated
Posts: 2713
|
posted May 14, 2010 11:30 PM
Megabyte,
That's different. Supra is suggesting that a worthwhile change would result from an increase in the free flow area, not filter media. Changing the porosity of the filter is a very different thing. The discussion isn't with or without filter, it's about making a 10% change in the opening area.
And, to make his expected 4 mph speed increase, say from 190 to 194 (about 2%), it would require a little more than 6% more power or about 11 hp. Like from 185 up to 196.
Doug
____________
It's not that I think you're dumb, it's just that so much of what you know isn't true....
|
shiphteey

Needs a job
Posts: 2529
|
posted May 15, 2010 03:52 AM
Supra, I appreciate your dedication and tinkering-mindedness. Just an fyi though, no one here is willing to voluntarily go SLOWER at a land speed event to prove you RIGHT. We travel too far, get too few runs, pay too much and do our best to datalog what our bike wants and doesn't want to waste a run or 2 doing it.
I think you should go look for a road near your area where you can do some runs and report back YOUR findings.
A.
____________
Gemini Motorcycles
Topping out everything from Ninja 250s to nitrous ZX-14s.
|
Shane661

Needs a life
Posts: 11494
|
posted May 15, 2010 03:55 AM
Am I wrong, or do you need to cut your frame up in order to test this mod?
That is a deal breaker for me.
|
supra5677
Pro
Posts: 1279
|
posted May 15, 2010 08:08 AM
I believe Megabyte is trying to say that the increased flow from the bmc air filter vs stock gives the engine more air to work with to make power. I'm along the same thinking with the increased air flow from 1 filter with more area than the stock 2.
2nd. Cutting up the frame is not apart of the process. A simple tool like a dremel and a few incisions removes the plate. It doesn't interfere with the integrity of the frame.
I agree with Doug. Someone please take my money if I am wrong I'll happily give it up
|
Shane661

Needs a life
Posts: 11494
|
posted May 15, 2010 08:10 AM
quote:
2nd. Cutting up the frame is not apart of the process. A simple tool like a dremel and a few incisions removes the plate. It doesn't interfere with the integrity of the frame.
To me, using a dremel to remove some inner braces of the frame is cutting the frame too much.
I'll gladly test the theory on your bike though, for free. Just bring it to Maxton.
|
Ken 12r

Novice Class
Posts: 86
|
posted May 15, 2010 09:52 AM
This is a bit like the ceramic bearings thread where people say they are worth X mph and somebody says it will be only Y mph because etc.etc. or the monster snorkel thread even.
The only way to tell is to get out on the landspeed course on the same day in the same conditions and do a number of back to back runs on the same bike with the same rider.
Only then will you have a clue if there is a significant difference,my money is on 2 bhp and point something of an MPH maximum gain which could easily vanish as quick as it appeared.
The main problem with the Zx12r we have found is that they do not like hot weather at all.
____________
www.uklandspeedracingassociation.co.uk
|
dougmeyer

Needs a job
moderated
Posts: 2713
|
posted May 15, 2010 05:40 PM
Right on, Ken
____________
It's not that I think you're dumb, it's just that so much of what you know isn't true....
|
psycho1122

Pro
Posts: 1608
|
posted May 16, 2010 04:32 AM
Yeah, My Ram SRT-10 RC does not like Hot weather either!!
____________
You say PSYCHO like it's a BAD thing!!
|
Phantom13

Zone Head
Posts: 736
|
posted May 16, 2010 10:09 AM
Edited By: Phantom13 on 16 May 2010 18:17
Supra, you do realize that it would be extremely expensive for Kawasaki to have placed that dividing piece in the airbox and redesign/mass produced the filters in order to slow down the bike. Why would Kawasaki go through that much trouble when they could simply reflash the ECU with less aggressive ignition and fuel maps to achieve the same goal.
A few key strokes and clicks of a mouse and you could kill 4-5mph of TOP SPEED by reflashing the ECU.... easily, quickly, and at no cost.
I'm pretty sure if someone in the R&D department suggested a 1" divider plate to be welded into the airbox along with a complete redesign and production of the air filters for the sole purpose of slowing down the 12R...... They'd be working at Burger King the next day.
I'm sorry Supra.... I enjoy reading about your wild theories and experiments, but I've got to say.....
YOU'RE CRAZY.
____________
"The only place Success comes
before Work is inside the Dictionary."
|
supra5677
Pro
Posts: 1279
|
posted May 16, 2010 06:18 PM
I don't mind if folks don't think my premise is plausible.
Fact remains plate is in there. How do we
know the production weren't changed to
add the plate. I am also familiar with re
flashing that was RR's project. The only way
to know is back to back runs ceterus
paribus.
|
supra5677
Pro
Posts: 1279
|
posted May 17, 2010 08:53 AM
Quote:
Why would Kawasaki go through that much trouble when they could simply reflash the ECU with less aggressive ignition and fuel maps to achieve the same goal.
Phantom 13 you CAN'T get 11 RWHP on a stock zx12r with more aggresive ignition and fuel curves. Thats 162 RWHP stock to 173. If its possible I would love to see it. I have the Ridge Racer ECU reflash.
|
Shane661

Needs a life
Posts: 11494
|
posted May 17, 2010 09:03 AM
Edited By: Shane661 on 17 May 2010 17:10
quote:
Phantom 13 you CAN'T get 11 RWHP on a stock zx12r with more aggresive ignition and fuel curves. Thats 162 RWHP stock to 173. If its possible I would love to see it. I have the Ridge Racer ECU reflash.
Phantom's point is: Why would Kawasaki re-tool the production line, at intense cost, in order to reduce performance? Instead of a "restrictor plate" they can just lop off the needed hp through the ecu.
Btw, are you still running the exhaust with the dual ZX-14 mufflers? How is that working out for you? It sure looks heavy.

What kind of header are you using with that setup?
|
supra5677
Pro
Posts: 1279
|
posted May 17, 2010 09:41 AM
That's a stock zx12r header with a custom made Y pipe. The mufflers are zx14 stock mufflers. I wanted the bike to look different. Before I had a 4-1-1 Akrapovic. Soon I am going to put on dual muzzy slip ons. The bike makes good power. I have after market cams, increased compression , and the Ridge Racer ECU mod. I still need to tune the ecu to the new pipes. I will wait until I put on the Muzzy Slip ons. WIith the dual set up bike seems to work better in the midrange.
supra
|
Shane661

Needs a life
Posts: 11494
|
posted May 17, 2010 09:43 AM
Photo provided by Supra:
|
supra5677
Pro
Posts: 1279
|
posted May 17, 2010 11:32 AM
The center plate was cearly added after the fact. If
you look at the lower gally it is
smooth all the way across. As far
as cost your not talking about that
much extra production time. Were
speculating of course.
|
Shane661

Needs a life
Posts: 11494
|
posted May 17, 2010 11:40 AM
Edited By: Shane661 on 17 May 2010 19:42
quote: The center plate was cearly added after the fact. If
you look at the lower gally it is
smooth all the way across. As far
as cost your not talking about that
much extra production time. Were
speculating of course.
It's not the time, it's the money.
Karl's bike makes over 235 hp without cutting up the frame. Do you think that your 175 hp 12R needs more air than that?
I find it ironic that you are chopping up your frame for supposedly more airflow into the engine, yet using a stock header with heavy dual ZX-14 cannisters. Where exactly do you think your aftermarket cam(s) and increased compression would likely be of most benefit? In the low rpm...or up high where you have a huge bottleneck in your exhaust flow via a stock header??
At any rate, good luck with your experiments.
|
thekaz

Needs a job
spell chequer is bustimicated
Posts: 2909
|
posted May 17, 2010 12:55 PM
quote: The center plate was cearly added after the fact. If
you look at the lower gally it is
smooth all the way across. As far
as cost your not talking about that
much extra production time. Were
speculating of course.
It is possible that it HAD to be added afterwards becuase the manufacturing process
It may not have possible to cast it properly or it got in the way of another process ??
Unless someone has the build sheet for that frame there is no way of knowing
|
supra5677
Pro
Posts: 1279
|
posted May 17, 2010 01:37 PM
Clearly the stock header doesn't perform as well the akrapovic! Anyways I'm on to another project I think. Probably an 89 zx10.
|
2000redrocket

Pro
Posts: 1662
|
posted May 17, 2010 02:10 PM
this a simple test. for those of you that do not use airfilters at maxton. just put them in after two runs to get a difference. or make two with them in and take them out and duct tape the filter area closed. if you go a lot faster than maybe a little bit of filter area may be worth it.
for me going from stock filters cleaned no oil to bmc race filters did not make me say for the 120 bucks hell yeah it was a kick in the pants. i am just saying i got trick filters now. which to me, takes away from saying all i got is a pipe and advancer at +2 deg. and a tricked ecu hehe.
|
Shane661

Needs a life
Posts: 11494
|
posted May 17, 2010 02:17 PM
Edited By: Shane661 on 17 May 2010 22:18
quote: this a simple test. for those of you that do not use airfilters at maxton. just put them in after two runs to get a difference. or make two with them in and take them out and duct tape the filter area closed. if you go a lot faster than maybe a little bit of filter area may be worth it.
for me going from stock filters cleaned no oil to bmc race filters did not make me say for the 120 bucks hell yeah it was a kick in the pants. i am just saying i got trick filters now. which to me, takes away from saying all i got is a pipe and advancer at +2 deg. and a tricked ecu hehe.
Anything beyond the filter surface area required for the maximum flow the engine requires is pointless.
|
2000redrocket

Pro
Posts: 1662
|
posted May 17, 2010 02:59 PM
i agree but what is stopping anyone from doing it? with no filters at all and seeing a pick up there may be a little bit to this, but i did not see crap to talk about going from stock to bmc except being 120 bucks leaner.
|
Phantom13

Zone Head
Posts: 736
|
posted May 17, 2010 03:04 PM
quote: Quote:
Why would Kawasaki go through that much trouble when they could simply reflash the ECU with less aggressive ignition and fuel maps to achieve the same goal.
Phantom 13 you CAN'T get 11 RWHP on a stock zx12r with more aggresive ignition and fuel curves. Thats 162 RWHP stock to 173. If its possible I would love to see it. I have the Ridge Racer ECU reflash.
Wow, Supra you really have no real world experience do you?
Ever tried playing with timing on back to back runs and see what happens to your speed with each degree added or subtracted from the map? How about with A/F ratio's? Ride height? Riding position? Filter media? etc, etc, etc....
I have.... and I'm telling you that you can EASILY kill 4+mph via the ECU on a stock bike. ANY STOCK BIKE!!!
It wouldn't take a huge change either, and it will still run great through the gears.... you'd probably never notice it unless you rung it out in 6th gear.
4mph is only like 250rpm!!!
You're talking about a 250 rpm drop at your top speed, that's it.
As for the divider piece being added afterwards.... there's a lot of things that could explain that. Maybe the airflow was too turbulent using one large filter? Maybe there was a problem with the structural integrity of the frame/airbox and that piece is acting as a brace? Maybe it was a casting issue? Who knows? I do know one thing.... you'd be fired on the spot from Kawasaki for even suggesting adding that divider piece as a means of neutering the bike.
That's just plain retarded.
____________
"The only place Success comes
before Work is inside the Dictionary."
|
supra5677
Pro
Posts: 1279
|
posted May 17, 2010 03:59 PM
Actually I am not retarded. But thats ok. The question is can you ADD 11 horsepower to a stock bike by reflashing the ECU. I don't think so. On a zx12r thats 162RWHP to 173. Everybody knows you can kill horsepower via the ECU. The question is how much can you add. Stock exhaust mind you.
I thought this thread was over.. but if others want to continue fine with me..
|
Shane661

Needs a life
Posts: 11494
|
posted May 17, 2010 04:02 PM
Edited By: Shane661 on 18 May 2010 00:08
quote: Actually I am not retarded. But thats ok. The question is can you ADD 11 horsepower to a stock bike by reflashing the ECU. I don't think so. On a zx12r thats 162RWHP to 173. Everybody knows you can kill horsepower via the ECU. The question is how much can you add. Stock exhaust mind you.
Uhhh, just let it rest, Forrest...
WTF are you talking about ..11 hp?
You add cams, compression, and then use a stock header with dual ZX-14 mufflers? Well, everyone can rest their case...your methodology = FAIL.
|
2000redrocket

Pro
Posts: 1662
|
posted May 17, 2010 04:51 PM
would you two stop beating him up for thinking on this.
|
|
|