HOME ARTICLES JOIN GALLERY STORE SPONSORS MARKETPLACE CONTACT US  
Register | FAQ | Search | Memberlist
Username:    Password:       Forgot your password?
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: 1349CC BIG BORE KIT? NEW TOPIC NEW POLL POST REPLY
Phantom13


Zone Head
Posts: 736
posted September 25, 2008 06:12 AM        
See that's just my point... how can you say, "There's no REPLACEMENT for displacement" when that rule only applies when the only thing you're allowed to change is .... displacement.


You may as well plug in ANYTHING and your rule still works. lol

"There's no replacement for a full exhaust" ....... so long as that's the only difference in two identical bikes.


Don't you see how ridiculous that sounds?


Oh well, believe what you want. I guess my little 1287cc N/A ZX-12R will continue beating every big bad stroker 12r at Maxton on pure luck. lol
____________
"The only place Success comes
before Work is inside the Dictionary."

  Ignore this member    Click here to visit Phantom13's homepage. 
Phantom13


Zone Head
Posts: 736
posted September 25, 2008 06:15 AM        
quote:
so why is 2.7 not a whole number?......



A whole number doesn't contain a fraction. A whole number is an integer which has 1 or more units and can be positive or negative.

58.1 is not a whole number.



____________
"The only place Success comes
before Work is inside the Dictionary."

  Ignore this member    Click here to visit Phantom13's homepage. 
Grunter


Parking Attendant
Posts: 29
posted September 25, 2008 12:43 PM        
shamelessly jumping in on this thread as i think its the best place to get my question answered, I realise nos is a cheaper way to go but that is an instant class change, I have a B1(02) zx12, looking to do a credible 200mph on it, looks like that is going to be standing mile. Its got Akra race pipe and can, PC3usb and the ignition module is on order to compliment the pc3, Been reading up on some the kits and some say bigger cc kits dont rev, not reliable etc... All I really want is first to reach the 200, then turn to 1/4s with a couple of mile runs throughout the year..and keep the bike useable on the street..approx 5000 miles per year...I appreciate the value of good setup etc..but I weigh in at 260 unsuited.. what would the best to aim for, would also be nice to have an edge on a stock/ piped 14 but cant have everything..lol

Cheers in advance guys...lots of good reading on this forum..

  Ignore this member   
Phantom13


Zone Head
Posts: 736
posted September 25, 2008 02:40 PM        Edited By: Phantom13 on 25 Sep 2008 22:50
With your size.... nitrous is the only way you're going 200mph in the standing mile.

With your current set-up and weight, most guys on 12's are running anywhere from 170-175mph in the standing mile, meaning you're probably going to need to find another 25-30mph to pull off that 200mph run.

Here at Ace Performance (www.AcePerformanceRacing.com) we built a 3mm overbore ZX-12R (1287cc) for a guy your size. With 195rwhp he went 194+mph naturally aspirated at Maxton. It's a very streetable and reliable Stage 2 engine that runs fine on 93oct pump gas. With a small very safe 30 shot of nitrous it would put him right at the 200mph mark for sure.




____________
"The only place Success comes
before Work is inside the Dictionary."

  Ignore this member    Click here to visit Phantom13's homepage. 
Megabyte


Pro
Posts: 1047
posted September 25, 2008 05:04 PM        
quote:
See that's just my point... how can you say, "There's no REPLACEMENT for displacement" when that rule only applies when the only thing you're allowed to change is .... displacement.


You may as well plug in ANYTHING and your rule still works. lol

"There's no replacement for a full exhaust" ....... so long as that's the only difference in two identical bikes.


Don't you see how ridiculous that sounds?


Oh well, believe what you want. I guess my little 1287cc N/A ZX-12R will continue beating every big bad stroker 12r at Maxton on pure luck. lol

____________
We First make our habits and then our habits make us.

  Ignore this member   
Megabyte


Pro
Posts: 1047
posted September 25, 2008 05:07 PM        Edited By: Megabyte on 26 Sep 2008 01:52
Congratulations on your victories @ Maxton.

Subtract that extra 87 cc of displacement and see if you still beat up the big boys. A number of times in my life with as many different bikes, I've been in a situation where I've done everything I could think of to make more power, and the only option left was to add more displacement. At that point, there was no replacement for more displacement, and that's my story and I'm sticking to it

quote:
See that's just my point... how can you say, "There's no REPLACEMENT for displacement" when that rule only applies when the only thing you're allowed to change is .... displacement.


You may as well plug in ANYTHING and your rule still works. lol

"There's no replacement for a full exhaust" ....... so long as that's the only difference in two identical bikes.


Don't you see how ridiculous that sounds?


Oh well, believe what you want. I guess my little 1287cc N/A ZX-12R will continue beating every big bad stroker 12r at Maxton on pure luck. lol

____________
We First make our habits and then our habits make us.

  Ignore this member   
KZScott


Needs a life
high on speed
Posts: 7235
posted September 25, 2008 06:04 PM        
quote:
quote:
so why is 2.7 not a whole number?......



A whole number doesn't contain a fraction. A whole number is an integer which has 1 or more units and can be positive or negative.

58.1 is not a whole number.





but it doesnt matter, unless you have other reasons you dont want to share. make the base spacer half the added stroke, time your cams....the stroke is taken care of, it doesnt matter if it was 57.75, 58, 51, or 60.4 its the same principle
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos

  Ignore this member   
KZScott


Needs a life
high on speed
Posts: 7235
posted September 25, 2008 06:12 PM        
quote:
See that's just my point... how can you say, "There's no REPLACEMENT for displacement" when that rule only applies when the only thing you're allowed to change is .... displacement.


You may as well plug in ANYTHING and your rule still works. lol

"There's no replacement for a full exhaust" ....... so long as that's the only difference in two identical bikes.


Don't you see how ridiculous that sounds?


Oh well, believe what you want. I guess my little 1287cc N/A ZX-12R will continue beating every big bad stroker 12r at Maxton on pure luck. lol


heres an idea. put Karls 1427 in your bike and see how fast it is @ maxton
you cant compare bikes that are setup differently. i can set my bike up to run really rich, but it would still beat a stock length (with perfect mapping) gsxr 1000 or busa in the 1/4.
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos

  Ignore this member   
Phantom13


Zone Head
Posts: 736
posted September 25, 2008 08:06 PM        
I'd rather have my 1287 than Karl's 1427...... But I'll take his carbon fiber wheels over my stockers anyday!

(no offense to Karl or JC.... )



____________
"The only place Success comes
before Work is inside the Dictionary."

  Ignore this member    Click here to visit Phantom13's homepage. 
osti33


Needs a job
Posts: 2973
posted September 25, 2008 09:36 PM        Edited By: osti33 on 26 Sep 2008 05:40
quote:
I'd rather have my 1287 than Karl's 1427...... But I'll take his carbon fiber wheels over my stockers anyday!

(no offense to Karl or JC.... )





Karl's bike doesn't have carbon fiber wheels. Never has. It has Marvic's on it.

  Ignore this member   
Chango


Expert Class
Posts: 165
posted September 26, 2008 05:22 AM        
stupid question here!

I have a 2000 12A with a yosh slip on and a PCIII I've had it well above 150 MPH. It seemed to have alot more left! Do you guys mean 200 in the 1/4 mile or do you just mean 200 period? Does this bike have the ability to hit the 200 mph mark in it's pretty much stock form ?

  Ignore this member   
Phantom13


Zone Head
Posts: 736
posted September 26, 2008 11:56 AM        
quote:
quote:
I'd rather have my 1287 than Karl's 1427...... But I'll take his carbon fiber wheels over my stockers anyday!

(no offense to Karl or JC.... )





Karl's bike doesn't have carbon fiber wheels. Never has. It has Marvic's on it.



Thanks for the correction, I almost ordered the Marvic Pumas.... but spent the loot on a fancy spancshy progressive nitrous controller and a custom nitrous system instead.
____________
"The only place Success comes
before Work is inside the Dictionary."

  Ignore this member    Click here to visit Phantom13's homepage. 
Kwaknut


Parking Attendant
Posts: 7
posted September 26, 2008 12:07 PM        
I'm running a 2001 ZX12 with mild mods - PC2, full Akropovic evolution exhaust, K&Ns. That puts 177bhp at the rear wheel, so it's not particularly high for a 12 when some break 180.

It also has a 50 shot wet nitrous system.

Without the nitrous, it leaves similarly tuned Hayabusas and GSX-R1000s for dead - just no competition, whether it's roll-on in 2nd or 3rd, or high-end blast up through the gears, and I've played with quite a few of each.

With the gas and a smaller rear sprocket she's made a measured 214mph.

I'm happy with stock displacement and a squirt of gas if I need it - keep the reliability and save a whole lot of money!

____________
It was the devil made me do it, officer.

  Ignore this member   
KZScott


Needs a life
high on speed
Posts: 7235
posted September 26, 2008 12:11 PM        
quote:
stupid question here!

I have a 2000 12A with a yosh slip on and a PCIII I've had it well above 150 MPH. It seemed to have alot more left! Do you guys mean 200 in the 1/4 mile or do you just mean 200 period? Does this bike have the ability to hit the 200 mph mark in it's pretty much stock form ?

200 in 1 mile. way harder than 200 period
you have to be making SERIOUS hp to get 200 in the 1/4.
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos

  Ignore this member   
Phantom13


Zone Head
Posts: 736
posted September 26, 2008 02:08 PM        
quote:
I'm running a 2001 ZX12 with mild mods - PC2, full Akropovic evolution exhaust, K&Ns. That puts 177bhp at the rear wheel, so it's not particularly high for a 12 when some break 180.

It also has a 50 shot wet nitrous system.

Without the nitrous, it leaves similarly tuned Hayabusas and GSX-R1000s for dead - just no competition, whether it's roll-on in 2nd or 3rd, or high-end blast up through the gears, and I've played with quite a few of each.

With the gas and a smaller rear sprocket she's made a measured 214mph.

I'm happy with stock displacement and a squirt of gas if I need it - keep the reliability and save a whole lot of money!




Measured "where" exactly?


____________
"The only place Success comes
before Work is inside the Dictionary."

  Ignore this member    Click here to visit Phantom13's homepage. 
dougmeyer


Needs a job
moderated
Posts: 2713
posted September 26, 2008 06:05 PM        Edited By: dougmeyer on 27 Sep 2008 02:10
The "1340" and "1349" 's were built soley to meet a an SCTA class limit for Bonneville which is 1350 cc. I built the first one in 2000, and another was built at Muzzys in 2002 for my record bike that year.We then built another one for Swft. (mine is for sale BTW). Over the years, a few more were built. (always for Bonneville, I'd assume)
Mine was over 200 hp, less than 210. It used a 1270 kit piston (custom dome) and a 3.1 (I think) mm crank. I just took the 1270 piston and picked a stroke that would give me a 1340. I kept it at 1340 because I did not want a mistake in tech to disqualify me. (It happens-that's only 2.5cc per cyl. and those tech guys aren't always the sharpest knives in the drawer)
It's a nice combination, but I'd just as soon do a 1361. The 1361 uses the same piston (stock cyl)with a +4mm crank (if I remember correctly). Most of these are around 200 hp out of the box.
Generally speaking, if you keep your ratios right and don't get too crazy, bigger is always better. Simply put displacement x rpm = power.

Oh yeah, and as far as the original question goes, I think it would make GREAT street bike.
Doug

____________
It's not that I think you're dumb, it's just that so much of what you know isn't true....

  Ignore this member   
KZScott


Needs a life
high on speed
Posts: 7235
posted September 26, 2008 06:23 PM        
so Doug, besides the not so sharp tech guys. with 86mm pistons (1287 pistons) would there be any draw back of going with a 2.7mm crank vs a 2.6mm crank?? (1349 vs 1347)
someone seems to think 2.7 is too much and i can figure out the reason . classified info i guess....
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos

  Ignore this member   
dougmeyer


Needs a job
moderated
Posts: 2713
posted September 27, 2008 03:00 AM        
Nope. But every combination is going to give a slightly different power curve and require different cam timing to be optimized,. So the more a particular combo is used, the more data there is.
____________
It's not that I think you're dumb, it's just that so much of what you know isn't true....

  Ignore this member   
Phantom13


Zone Head
Posts: 736
posted September 27, 2008 06:16 AM        
quote:
Congratulations on your victories @ Maxton.

Subtract that extra 87 cc of displacement and see if you still beat up the big boys. A number of times in my life with as many different bikes, I've been in a situation where I've done everything I could think of to make more power, and the only option left was to add more displacement. At that point, there was no replacement for more displacement, and that's my story and I'm sticking to it





I don't need to subtract the 87cc's to make my point valid. According to your "theory" my 195rwhp 1287 shouldn't be anywhere close to running the speeds of let's say Karl's 225rwhp 1427, correct? Yet my little 1287 has gone faster with a 50lb heavier rider and stock wheels, NO DATALOGGING, not even slammed and strapped down. Hell, my bike has NEVER EVEN BEEN ON A DYNO. So explain to me how all this is possible if "there's no replacement for displacement".

What you're failing to understand is that there are OTHER WAYS to get performance out of an engine besides adding cc's. There IS a replacement and my 1287 is living proof of it.

But whatever... I guess when you live in a 2 dimensional world, it's hard to see around corners.
____________
"The only place Success comes
before Work is inside the Dictionary."

  Ignore this member    Click here to visit Phantom13's homepage. 
Phantom13


Zone Head
Posts: 736
posted September 27, 2008 06:24 AM        
quote:
so Doug, besides the not so sharp tech guys. with 86mm pistons (1287 pistons) would there be any draw back of going with a 2.7mm crank vs a 2.6mm crank?? (1349 vs 1347)
someone seems to think 2.7 is too much and i can figure out the reason . classified info i guess....



Yes, it is G14 classified info. lol


To be honest... ONE of the reasons is what Doug mentioned about tech inspection, but that's not the main reason. Believe it or not, there's a lot of factors that push towards the use of a 2.6mm stroke over a 2.7mm on 86mm pistons, at least when building an EXCEPTIONAL LSR ENGINE.

Of course, any Tom, Dick, and Harry can slap together some big cams, big cc's, and a hogged out head that will make killer power... on the dyno, but that doesn't mean it's going to run worth a damn out in the real world. Some people just place too much faith in what the dyno tells them and they usually get spanked by the people who put faith into what the GPS tells them.

Anyway, I'm done with this thread... .I've already said too much as it is! lol
____________
"The only place Success comes
before Work is inside the Dictionary."

  Ignore this member    Click here to visit Phantom13's homepage. 
Kwaknut


Parking Attendant
Posts: 7
posted September 27, 2008 11:55 AM        
quote:
stupid question here!

I have a 2000 12A with a yosh slip on and a PCIII I've had it well above 150 MPH. It seemed to have alot more left! Do you guys mean 200 in the 1/4 mile or do you just mean 200 period? Does this bike have the ability to hit the 200 mph mark in it's pretty much stock form ?
Not a stupid question.

So many people have claimed 200mph with that sort of setup, while reality is probably low-mid 190s unless you've found a hell of a strong tail wind.

Even with the power, I think stock gearing needs to be changed a little to break a real 200.
Plenty of 12s will show 200mph on the dial, but like most bikes and cars it will be over-reading.
____________
It was the devil made me do it, officer.

  Ignore this member   
Kwaknut


Parking Attendant
Posts: 7
posted September 27, 2008 11:57 AM        
quote:
quote:
I'm running a 2001 ZX12 with mild mods - PC2, full Akropovic evolution exhaust, K&Ns. That puts 177bhp at the rear wheel, so it's not particularly high for a 12 when some break 180.
It also has a 50 shot wet nitrous system.
Without the nitrous, it leaves similarly tuned Hayabusas and GSX-R1000s for dead - just no competition, whether it's roll-on in 2nd or 3rd, or high-end blast up through the gears, and I've played with quite a few of each.
With the gas and a smaller rear sprocket she's made a measured 214mph.
I'm happy with stock displacement and a squirt of gas if I need it - keep the reliability and save a whole lot of money!


Measured "where" exactly?

Wow - sounds like you're being a little confrontational and challenging.

On a stretch of tarmac.
____________
It was the devil made me do it, officer.

  Ignore this member   
KZScott


Needs a life
high on speed
Posts: 7235
posted September 27, 2008 12:42 PM        
he wont believe you unless you can prove it was at a sanctioned event like the maxton mile or texas mile(if it was from a standing start in a mile). but if you had more than a mile im sure you did pull that mph with that kind of hp
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos

  Ignore this member   
Grunter


Parking Attendant
Posts: 29
posted September 27, 2008 01:45 PM        
quote:
With your size.... nitrous is the only way you're going 200mph in the standing mile.

With your current set-up and weight, most guys on 12's are running anywhere from 170-175mph in the standing mile, meaning you're probably going to need to find another 25-30mph to pull off that 200mph run.

Here at Ace Performance (www.AcePerformanceRacing.com) we built a 3mm overbore ZX-12R (1287cc) for a guy your size. With 195rwhp he went 194+mph naturally aspirated at Maxton. It's a very streetable and reliable Stage 2 engine that runs fine on 93oct pump gas. With a small very safe 30 shot of nitrous it would put him right at the 200mph mark for sure.






Thanks for the info..had a read of your site and it certainly sounds like the cheaper option.. the 195rwhp engine was that down to the capacity increase alone or was other work carried out..ie porting, increased inlet valves etc.. I think i would be happy with 195hp for street use, our fuel is a little higher octane in the UK, think its normally 95 or 96 but 99,100,105 available at pumps, would this be an issue?...

...214mph on 01 zx12, what top speed delimiter are you using and are there any issues with the power commander? Asking as I need one for mine and havent decided which to go for yet.

  Ignore this member   
KZScott


Needs a life
high on speed
Posts: 7235
posted September 27, 2008 02:05 PM        
the muzzy bonny box takes out the lower rev limiter in 6th (effectivly getting rid of the speed limiter, which is 300km/h using stock gearing)
or get the ecu hacked
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos

  Ignore this member   
All times are America/Va [ This thread is 4 pages long: 1  2  3  4     Next» ] < Previous Thread     Next Thread >
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: 1349CC BIG BORE KIT? NEW TOPIC NEW POLL POST REPLY

FEATURED NEWS   Bikeland News RSS Feed

HEADLINES   Bikeland News RSS Feed


Copyright 2000-2026 Bikeland Media
Please refer to our terms of service for further information
0.3181300163269 seconds processing time