KZScott

Needs a life
high on speed
Posts: 7235
|
posted August 28, 2008 05:49 PM
yes, the Muzzy 1317 is the offset block. we cant get anything bigger. SBM did an 87 that wasnt offset though, but the cylinder walls are a lot thinner than the Muzzy
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos
|
aliveagain

Needs a life
Posts: 5033
|
posted August 28, 2008 07:01 PM
quote: I don't recollect that the 1317 is an offset block. It is simply a billet big block with concentric 87mm cylinders. Right Karl? In its original form you had to clearance the cases for the lower portion of the cylinders. Later we modified that so it was stricty a "top end" change. Actually, like you put it ,"a weekend job".
The next larger block was the offset one.
Never heard of the next larger block.There is one larger than 1317?
____________
I wondered why the baseball kept getting bigger. Then it hit me.
|
entropy
Moderator
Posts: 8671
|
posted August 29, 2008 02:44 AM
quote: yes, the Muzzy 1317 is the offset block. we cant get anything bigger. SBM did an 87 that wasnt offset though, but the cylinder walls are a lot thinner than the Muzzy
that ole KZ does his homework.
____________
This moderator uses moderation in moderation
|
rgeorge

Expert Class
Posts: 220
|
posted August 29, 2008 05:41 AM
Muzzy also offered an 84mm "turbo block" that was not offset.
|
Dane
Expert Class
Posts: 235
|
posted August 29, 2008 07:20 PM
Ok, here comes the stupid question. Why run an offset cylinder and crankshaft? Wall thickness between cylinders?
|
KZScott

Needs a life
high on speed
Posts: 7235
|
posted August 29, 2008 07:37 PM
exactly. you can go with bigger bores and maintain cylinder wall thickness between them. thin walls can cause heat issues and headgasket issues.
the only thing i can think of bigger than the 87mm block, was the 88mm block that Rob posted about yrs ago on the dragbike.com forums. i dont think it was ever built though. that combined with a huge stroke made a 1508cc bike if im rembering correctly. the largest motor that was practical. (keep going, and pretty soon you have a billet motor that is based on a zx12r, but shares little to no stock parts)
____________
01 ZX-12R 8.84 @ 156.3 no bars, DOT tires. Pump Gas, NA.... turbo 8.47 @ 164.
00 ZX-12R 8.62 @ 165.2 no bars, slicks, Pump Gas, 55 shot.... turbo 8.32 @173
00 ZX-12R Fastest NA Kawasaki in the world 1: 222.046 1.5: 226.390 Loring AFB
00 ZX-12R street turbo 1: 227.9 1.5: 234.1 Loring AFB
00 ZX-12R LSR turbo 1: 263.1 1.5: 266.5 Loring AFB Worlds fastest ZX-12R
CMG Racing RCC Turbos
|
dougmeyer

Needs a job
moderated
Posts: 2713
|
posted August 30, 2008 07:50 PM
All correct. I kind of got lost in all the combos that were running around in '04. My bad. Lot's of 1317 blocks are in the field without problems. I know Entropy had piston interference problems, but that wasn't something that was common when I was there.
I'll be visiting him soon. Maybe he'll show me the parts........
Thanks for setting me straight KZ.
Doug
____________
It's not that I think you're dumb, it's just that so much of what you know isn't true....
|
2000redrocket

Pro
Posts: 1662
|
posted August 31, 2008 06:26 PM
with my drag car and the new for me anyway builder what doug said is important on setting up the whole engine.
short/ bad rod ratio engines typically use a more advanced cam centerline than a longer one again due to dwell time.
shorter rods tend to make better lowend power with the leverage on the crank angle but have more side load on piston at high revs but the longer rod engine will have less friction and the way he said will develop more higher hp.
my dusters cam was 110 lobe center installed at 104deg.with the 6.7" rod vs stroke he said there was a lot of valve action with not much piston movement due to the longer dwell time wasting some duration with not much movement.and i think his point works cause my engine made peek torque at 4800rpm at 590ftlb.
the stuff he is fixing should make the air under the front more i think. i just do not want to pee my pants on first launch.
|
|
|