HOME ARTICLES JOIN GALLERY STORE SPONSORS MARKETPLACE CONTACT US  
Register | FAQ | Search | Memberlist
Username:    Password:       Forgot your password?
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: hindle or muzzy NEW TOPIC NEW POLL POST REPLY
hbeat12R


Parking Attendant
Posts: 25
posted April 23, 2004 10:10 PM        
zx12haitian, have you experienced a jumpy idle with your muzzy exhaust? If so, what is the fix? Any info is appreciate...thanks!

  Ignore this member     
Hells Dark Lord


Needs a life
living life, and loving it.
Posts: 7981
posted April 24, 2004 03:36 AM        
Hbeat....most everyone's bike get an off idle stumble with the Muzzy pipe. If you take it to a good shop that can tune it with a dyno they should be able to make a map and get ride of that stumble. After the Muzzy was added, I tried lots of generic maps, some work better than others. It was very annoying around town, so I called kcadby and he hooked it up for me, and it runs great. The Muzzy stumble is not uncommon, and I see that you asked if it were on Muzzy's website? I dont know if it is, but if you did any research at all about that product, espicially on here, you would have found that out easily. Do a search of this forum and see what comes up.

Take some time with it, adn spend the money for a good map...some guys on here say ya dont need one, hell some dont even run PC's. BUt I am a firm believer in it.....JMO......Jim
____________
When in doubt, lean farther and go faster....

  Ignore this member   
canadamaxxer


Pro
Posts: 1090
posted April 24, 2004 08:01 AM        
No idle issues with the 1270 kit and the stepped Hindle on my bike. Does Hindle know something that Muzzy doesn't???

I looked at that pilot jet mod and really dislike the idea of isolating the intake air pressure sensor behind an oriface. I understand the concept of smoothing the air pulses to the sensor, but an oriface such as that pilot jet installed into the vacuum line to the IAP sensor will also cause a delay in the sensor receiving the vacuum signal change. To me this means that the IAPS will always be lagging behind (whenever there is a change in intake pressure i.e.: closed to open throttle, or vice versa...or somewhere in between). Fuel and timing delivery calculations are based on getting the proper data at the proper time. If the ECU gets the the info late, the speed/density calculcations are off, and I'm willing to bet that this results in an overly rich condition when decellerating with a closed throttle. I read the posts from the other forums and there is one guy complaining about fouling and sooty plugs....and as soon as he removed the oriface the problem went away. To me it seems like this is a bandaid repair.

In my opinion, driveability issues that can't be ironed out with the support of the company that supplied the aftermarket parts should be the responsiblity of the supplier to resolve....or take the part back. We have accepted that a Power Commander (or Equivalent) is needed to iron out the driveability issues with these parts...and to get the maximum gain, but to go beyond that to cover up the (poor?) engineering of the parts is a little ridiculous. I guess it's all about compromise: a pipe manufacturer may leave a driveability flaw somewhere in the low end of the RPM range out of neccesity to get the gains they need at the high RPM's (pipe diameter, collector length, 4-1 vs 4-2-1, etc...even the material used are used to tune the pipe for specific driving conditions). Then we as the end users come along and want that flaw covered up because the vehicle drives terribly in the real world. This is where the band aid fixes seem to come in..."install a resistor here, plug this off, switch these wires, etc, etc". Who is responsible for making the bike run properly? The aftermarket companies (my experience is with both motorcycle and automotive performance) typically respond with "we can't possibly predict every running condition....your air must be different in ______(insert your province/state name here)". Dynojet is a great example: I bought a stage 1 kit for my VMAX. In the kit it states that if you have an aftermarket pipe and air filter, you need to install this jet (a DJ 180), if the bike is stock you need to install that jet (a DJ 165). I installed the 180 jet and almost had fuel running out of the end of the pipe. I called Dynojet and got the "we've never heard of that before.....have you checked your float height? You might want to lower it to ___(whatever)" response. I went online and asked around. The response was "yeah those jets are great if you live 500 ft BELOW sea level". I ended up re-installing the stock main jets. Some tech support, eh?


To me the bottom line is: if a person has to go to ridiculous lengths to make a poorly designed product work (anyone would be pissed to buy a body panel and then find out that none of the mounting holes line up. That part would get returned pronto; and yet we install pipes, etc and when the bike runs worse we accept that as a "tuning challenge".), then the manufacturer (I don't care what manufacturer it is....my VMAX had a Hindle at one point in time..and it never ran right with that pipe..installed a different pipe and everything was great) should be (at least partially) responsible for assisting in making things right. Muzzy's has Maps available...why don't their maps fix this off idle stumble?...if a good custom made Map can eliminate the problem, so can Muzzys' Map.

  Ignore this member   
DaveInDaytona


Pro
Posts: 1696
posted April 24, 2004 05:27 PM        
'02's and newer shouldn't have the idle hunt with the right map. It was a new game when they came out with the new ECU. Even the earlier ones could be made pretty good.

A good map is the key, and when it's done the only way to get a good one is to have a guy doing the numbers that knows what they are doing. The stock Muzzys map is for their bike on their dyno, all the bikes are a little different and I doubt they spent much time idle tweaking because if I remember right Doug's answer to the idle hunt is to crank that control on the right handlebar, that will make you forget the idle.
____________
DaytonaSportbikes Forum

  Ignore this member    Click here to send DaveInDaytona an AIM message. 
TurboBlew


Moderator
BUSY DOING THE SCHIAVO
Posts: 4590
posted April 24, 2004 07:17 PM        
2004 and numerous posts from Doug and we still get the same shit.....lol

I had a Muzzy on both my 2000 and 2002. Only reason I switched because EVERYONE had a Muzzy.... I like to be different.
Great pipes for the $$. The carbon cans need more maintenance than I wanted.. but other than those minor details Id recommend one to anybody.

I have an Akrapovic pipe as well. Good quality as well... a tad better than Muzzys.. but they also cost nearly double!! While I can appreciate art and all..... I find that the $1200 an Akra costs would be better spent on other items to compliment my $600 Muzzy.

____________
Official Charter Member of the RIDERS OF KAWASAKI MEMBERSHIP REVOCATION CLUB
Also a BadAss Internet Forum Moderator 4 Hire!! Come at me brah!

  Ignore this member   
All times are America/Va [ This thread is 3 pages long: 1  2  3   ] < Previous Thread     Next Thread >
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: hindle or muzzy NEW TOPIC NEW POLL POST REPLY

FEATURED NEWS   Bikeland News RSS Feed

HEADLINES   Bikeland News RSS Feed


Copyright 2000-2026 Bikeland Media
Please refer to our terms of service for further information
0.26578998565674 seconds processing time