kawasakijockey
Pro
Posts: 1876
|
posted May 26, 2012 11:59 AM
305lb unsuited rider runs 9.30's on new 14. Who?
In Houston last night at RPR says the little birdie. Stock motor with an arm. Thought maybe it was a member here.
____________
Get on the shortbus boys 'cause its time to get schooled.
2007 ZX-14
1.38 60ft
9.03 @ 149mph
8.95 @153 small shot n2o
8.68 @160mph 5lbs boost
  
|
Wheelie
Needs a life
Old Man
Posts: 6902
|
posted May 26, 2012 12:16 PM
quote:
In Houston last night at RPR says the little birdie. Stock motor with an arm. Thought maybe it was a member here.
Sasquatch?
wee
|
zx12mark
Pro
Posts: 1654
|
posted May 26, 2012 12:30 PM
that poor bike.that means i could run 8.90s being i weigh 135.............we will find out this summer..
|
dcjens
Pro
Wet side of Washington
Posts: 1059
|
posted May 26, 2012 01:07 PM
This is why Im not rushing out to buy an R...my 06 with my 155lb self...its still faster than shit. I flap in the wind
____________
Black 06
|
codyc_13
Expert Class
Posts: 342
|
posted May 26, 2012 01:29 PM
This bike was at the PMRA race past weekend, rider looks about that weight. According to a unconfirmed source it was running 9.10s 
____________
06 zx14, 65", lowered, muzzy pipe, pcIII, air shifter, Litz revalve, Adams cut seat, OSR cut pan 87 pump gas.
8.97 at 149mph
|
codyc_13
Expert Class
Posts: 342
|
posted May 26, 2012 01:34 PM
Correction, looks like I had bad info. Looked through some more pics and found this. There was a bike dialed 9.07, but it was a much smaller rider 
____________
06 zx14, 65", lowered, muzzy pipe, pcIII, air shifter, Litz revalve, Adams cut seat, OSR cut pan 87 pump gas.
8.97 at 149mph
|
kawpower
Zone Head
Mr kawasaki 2 you!
Posts: 887
|
posted May 26, 2012 01:56 PM
he looks about my weight 312 suited, i was running that on my 06 at 63inches pumpgas bmc filter, tsukigi street pipe .powercommander! i am shure once he gets more seat time he should run 9.40s !
____________
Cecil County 2010 Motorcycle ET Champ. 9 Wins- 4 RUs .06zx14 turboed for 2012 .
|
Audio
Expert Class
Posts: 117
|
posted May 26, 2012 02:06 PM
 Edited By: Audio on 26 May 2012 22:23
That photo is me, I weigh 280 suited bike weight is 520 800 lbs total on there scales.
Best pass on it has been 9.69 @ 142 has a pipe, PCV, JC tune and 8 over arm.
The other green 14 there weight was 725 total and it ran 9.07.
____________
Audio
2008 ZX14 Old Gray CNC-1414 old new CNC ?
2012 ZX14R SE Green CNC-?
|
codyc_13
Expert Class
Posts: 342
|
posted May 26, 2012 02:34 PM
Did you happen to throw the bike on the dyno at the PMRA race? 142 is strong MPH at your weight in noble.
____________
06 zx14, 65", lowered, muzzy pipe, pcIII, air shifter, Litz revalve, Adams cut seat, OSR cut pan 87 pump gas.
8.97 at 149mph
|
Audio
Expert Class
Posts: 117
|
posted May 26, 2012 02:52 PM
i did @ the 1st PMRA race it made 183 stock with stock pipes. Went 9.95 @ 138
Then Johnny Cheese tuned it with a pipe and PCV dyno sheet posted in this form.
That photo was the 2nd race.
____________
Audio
2008 ZX14 Old Gray CNC-1414 old new CNC ?
2012 ZX14R SE Green CNC-?
|
Audio
Expert Class
Posts: 117
|
posted May 26, 2012 02:54 PM
Edited By: Audio on 26 May 2012 22:55
quote:
he looks about my weight 312 suited, i was running that on my 06 at 63inches pumpgas bmc filter, tsukigi street pipe .powercommander! i am shure once he gets more seat time he should run 9.40s !
Yes I still went faster on my 08 (pipe pc3 w/ ext) than I have on this 2012 by a solid tenth.
____________
Audio
2008 ZX14 Old Gray CNC-1414 old new CNC ?
2012 ZX14R SE Green CNC-?
|
BLK ICE
Pro
we'll leave the light on for u
Posts: 1709
|
posted May 26, 2012 02:59 PM
Edited By: BLK ICE on 26 May 2012 23:29
quote:
i did @ the 1st PMRA race it made 183 stock with stock pipes. Went 9.95 @ 138
Then Johnny Cheese tuned it with a pipe and PCV dyno sheet posted in this form.
That photo was the 2nd race.
What was your 1/8 e/t?
Looks like you may have a little something for the "haters" hanging on that arm.?
____________
Fastest Stock Motor, Stock Bodywork, Hand Clutch, N/A Super Heavy Hitter on the Planet!
Fastest Stock Motor, Stock Bodywork, Hand Clutch, Nitrous Super Heavy Hitter on the Planet!
Bikeland 1/8 mile 5 sec.N/A Stock Motor Club Member.
Repersenting: BLACK ICE PERFORMANCE and NO QUARTER MOTORSPORTS
Nitrous and Tires Sponsored by: Custom Specialties Cycles
Dyno Tuned by: Garron of ADAMS PERFORMANCE. http://www.adamsperformance.net/
BlackIce Performance: Honor, Freedom, Love of Country!
(I am open to Sponsorship and Product Testing and Review. Contact BlackIce Performance at blackice_performance@yahoo.com) or BlackIce Perf on Facebook
|
codyc_13
Expert Class
Posts: 342
|
posted May 26, 2012 03:55 PM
quote:
i did @ the 1st PMRA race it made 183 stock with stock pipes. Went 9.95 @ 138
Then Johnny Cheese tuned it with a pipe and PCV dyno sheet posted in this form.
That photo was the 2nd race.
Nice, just for comparison my 06 with a full exhaust and pc3 made 170 on that dyno.
____________
06 zx14, 65", lowered, muzzy pipe, pcIII, air shifter, Litz revalve, Adams cut seat, OSR cut pan 87 pump gas.
8.97 at 149mph
|
Audio
Expert Class
Posts: 117
|
posted May 26, 2012 06:37 PM
quote:
quote:
i did @ the 1st PMRA race it made 183 stock with stock pipes. Went 9.95 @ 138
Then Johnny Cheese tuned it with a pipe and PCV dyno sheet posted in this form.
That photo was the 2nd race.
What was your 1/8 e/t?
Looks like you may have a little something for the "haters" hanging on that arm.?
Stock ran 6.53 with pipe tune and PCV 6.27 1/8 not sure on mph didnt look
____________
Audio
2008 ZX14 Old Gray CNC-1414 old new CNC ?
2012 ZX14R SE Green CNC-?
|
1badzx12r
Needs a life
Posts: 8321
|
posted May 26, 2012 07:59 PM
quote:
quote:
i did @ the 1st PMRA race it made 183 stock with stock pipes. Went 9.95 @ 138
Then Johnny Cheese tuned it with a pipe and PCV dyno sheet posted in this form.
That photo was the 2nd race.
Nice, just for comparison my 06 with a full exhaust and pc3 made 170 on that dyno.
with same mods my 06 made 189 on that dyno too.
____________
http://www.youtube.com/watch?v=S06nIz4scvI
|
codyc_13
Expert Class
Posts: 342
|
posted May 26, 2012 08:08 PM
quote:
quote:
quote:
i did @ the 1st PMRA race it made 183 stock with stock pipes. Went 9.95 @ 138
Then Johnny Cheese tuned it with a pipe and PCV dyno sheet posted in this form.
That photo was the 2nd race.
Nice, just for comparison my 06 with a full exhaust and pc3 made 170 on that dyno.
with same mods my 06 made 189 on that dyno too.
On the Huckabay brothers dyno? Crazy that a dyno will vary that much. Guess that's why they are good as tuning tools only.
____________
06 zx14, 65", lowered, muzzy pipe, pcIII, air shifter, Litz revalve, Adams cut seat, OSR cut pan 87 pump gas.
8.97 at 149mph
|
edszx14
Expert Class
Posts: 271
|
posted May 26, 2012 08:11 PM
Hey KawasakiJockey, were you at RPR last night, 5/25/2012. I was there. There was quite a few bikes and two of the bright green new 14r. I was there with my 08 SE 14, the red and black one. If you were there, sorry I missed you.
____________
Ed
|
kawasakijockey
Pro
Posts: 1876
|
posted May 26, 2012 08:19 PM
I was not there Ed but a friend was and he called me.
____________
Get on the shortbus boys 'cause its time to get schooled.
2007 ZX-14
1.38 60ft
9.03 @ 149mph
8.95 @153 small shot n2o
8.68 @160mph 5lbs boost
|
edszx14
Expert Class
Posts: 271
|
posted May 26, 2012 08:32 PM
That is a very nice track. it was sticking real good last night and has a long shut down area.
____________
Ed
|
kawasakijockey
Pro
Posts: 1876
|
posted May 26, 2012 08:40 PM
Yeah, I have run there about 5 times this year.
____________
Get on the shortbus boys 'cause its time to get schooled.
2007 ZX-14
1.38 60ft
9.03 @ 149mph
8.95 @153 small shot n2o
8.68 @160mph 5lbs boost
|
1badzx12r
Needs a life
Posts: 8321
|
posted May 27, 2012 04:44 AM
quote:
quote:
quote:
quote:
i did @ the 1st PMRA race it made 183 stock with stock pipes. Went 9.95 @ 138
Then Johnny Cheese tuned it with a pipe and PCV dyno sheet posted in this form.
That photo was the 2nd race.
Nice, just for comparison my 06 with a full exhaust and pc3 made 170 on that dyno.
with same mods my 06 made 189 on that dyno too.
On the Huckabay brothers dyno? Crazy that a dyno will vary that much. Guess that's why they are good as tuning tools only.
NO cheese's dyno
____________
http://www.youtube.com/watch?v=S06nIz4scvI
|
codyc_13
Expert Class
Posts: 342
|
posted May 27, 2012 05:44 AM
Ok, I was talking about the dyno they have setup at the PMRA races.
____________
06 zx14, 65", lowered, muzzy pipe, pcIII, air shifter, Litz revalve, Adams cut seat, OSR cut pan 87 pump gas.
8.97 at 149mph
|
Audio
Expert Class
Posts: 117
|
posted May 27, 2012 07:03 AM
quote:
Ok, I was talking about the dyno they have setup at the PMRA races.
The 183 stock was on the dyno @ PMRA.
I will put it on there next race again to see difference he was to busy @ the last race.
____________
Audio
2008 ZX14 Old Gray CNC-1414 old new CNC ?
2012 ZX14R SE Green CNC-?
|
boostphreak
Expert Class
Posts: 168
|
posted May 27, 2012 09:57 AM
quote:
quote:
quote:
quote:
quote:
i did @ the 1st PMRA race it made 183 stock with stock pipes. Went 9.95 @ 138
Then Johnny Cheese tuned it with a pipe and PCV dyno sheet posted in this form.
That photo was the 2nd race.
Nice, just for comparison my 06 with a full exhaust and pc3 made 170 on that dyno.
with same mods my 06 made 189 on that dyno too.
On the Huckabay brothers dyno? Crazy that a dyno will vary that much. Guess that's why they are good as tuning tools only.
NO cheese's dyno
a dyno will vary from day to day depending on the weather. thats why you should use the same dyno evertime. (if you are using it as a tuning tool and not for bragging rights)
|
1badzx12r
Needs a life
Posts: 8321
|
posted May 27, 2012 10:29 AM
quote:
quote:
quote:
quote:
quote:
quote:
i did @ the 1st PMRA race it made 183 stock with stock pipes. Went 9.95 @ 138
Then Johnny Cheese tuned it with a pipe and PCV dyno sheet posted in this form.
That photo was the 2nd race.
Nice, just for comparison my 06 with a full exhaust and pc3 made 170 on that dyno.
with same mods my 06 made 189 on that dyno too.
On the Huckabay brothers dyno? Crazy that a dyno will vary that much. Guess that's why they are good as tuning tools only.
NO cheese's dyno
a dyno will vary from day to day depending on the weather. thats why you should use the same dyno evertime. (if you are using it as a tuning tool and not for bragging rights)
That said map suck at the track and lost mph .. i went back to the old map that i datalogged from run time .. i believe dyno's are worthless for tuning to real world air .. good for a starting point but at 300.00 its an expensive starting point ...
____________
http://www.youtube.com/watch?v=S06nIz4scvI
|
|
|
HOME
NEW TOPIC