87gtNOS
Zone Head
Posts: 620
|
posted December 17, 2011 03:13 PM
http://s1091.photobucket.com/albums/i399/kawitom/?action=view¤t=dyno004.mp4
____________
01 ZX12R
07 ZX14 - YEAH BABY!
03 ZX9R-traded in for the 14!!! June 07!
05 636-traded in for the 9 Sept 05
  
|
smokinZX14
Needs a life
Posts: 10197
|
posted December 17, 2011 03:54 PM
Must have gone into defalt mode of some kind ..Still 189 hp at 10k is very good ...
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
Compton
Zone Head
Posts: 969
|
posted December 17, 2011 04:44 PM
wow that dyno room is scary. i'd hate to see what happens when an engine lets loose and causes a fire
____________
b.w.
zx14, little longer, little louder, little lower.
08 Busa, just a little longer and louder and lower than the 14
|
Johnnycheese
Pro
Posts: 1008
|
posted December 18, 2011 06:25 AM
no load control and where is it getting fresh air from??????
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas
|
KAWITOM
Expert Class
My 12R gone but not forgotten
Posts: 218
|
posted December 18, 2011 06:37 AM
The room is bigger than it looks, it has been that way for seven or eight years alot of bikes have been on that dyno everything from pro street to regular streetbikes. He has lots of fans that you can't see in the room, yea it isn't room designed by dynojet, but he knows what he's doing, he's the tuner of the worlds fastest snowmobile, it's a custom chassis with turbo hayabusa motor in it with a chain drive setup and air shifter. Has gone 186 mph in 1000 ft. on ice, so I trust him
____________
2012 ZX-14R SE
2002 VULCAN MEAN STREAK (11.41 @ 114 best 1/4)
I BLEED GREEN
|
Wheelie
Needs a life
Old Man
Posts: 6902
|
posted December 18, 2011 08:25 AM
KAWITOM, did the tc wire have to be lengthened on the rear? How long is your swingarm?
wee
|
KAWITOM
Expert Class
My 12R gone but not forgotten
Posts: 218
|
posted December 18, 2011 09:12 AM
Wanted to say thanks for making that video work 87gt I appreciate it, Wheelie I am at 67 1/2". I measured and I am at about 8" inches over. The TC sensor wire is long enough, but instead of looping the wire over the top I had to go under the swingarm if you don't want to lenghten the wire, but if I remember Wheelie your gonna be longer than 8" so your probably gonna have to lenghten the wire cause is just long enough at 8"
____________
2012 ZX-14R SE
2002 VULCAN MEAN STREAK (11.41 @ 114 best 1/4)
I BLEED GREEN
|
smokinZX14
Needs a life
Posts: 10197
|
posted December 18, 2011 01:18 PM
quote:
Wanted to say thanks for making that video work 87gt I appreciate it, Wheelie I am at 67 1/2". I measured and I am at about 8" inches over. The TC sensor wire is long enough, but instead of looping the wire over the top I had to go under the swingarm if you don't want to lenghten the wire, but if I remember Wheelie your gonna be longer than 8" so your probably gonna have to lenghten the wire cause is just long enough at 8"
Tom who made the arm and was it 10 or 12 over ? Thanks ..
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95
|
JZX
Zone Head
Posts: 943
|
posted December 18, 2011 02:04 PM
Smokin, it looks like an evil arm.
____________
06 ZX14 65"
Best 1/8 mile 5.68@126.4 on a 1.41 60'
Best 1/4 mile 8.87@152.7 on a 1.47 60'
|
KAWITOM
Expert Class
My 12R gone but not forgotten
Posts: 218
|
posted December 18, 2011 02:13 PM
Lee it's an Adam's performance strongarm meant for a gen 06 to 011. It has four inches of adjustment, on the new bike from center of pivot bolt to center of axle spots its 29 1/2 to 33 1/2. Stock arm is 23 1/2 , so I was wrong I am more like 9 + and I have another 1" of adjustment. If anybody is looking for one there is one for sale on the other site in classified for $600.00,
The sensor wire is maxed out at around 9", unless you lengthen it
____________
2012 ZX-14R SE
2002 VULCAN MEAN STREAK (11.41 @ 114 best 1/4)
I BLEED GREEN
|
JZX
Zone Head
Posts: 943
|
posted December 18, 2011 02:18 PM
I like that arm- easy install?
____________
06 ZX14 65"
Best 1/8 mile 5.68@126.4 on a 1.41 60'
Best 1/4 mile 8.87@152.7 on a 1.47 60'
|
KAWITOM
Expert Class
My 12R gone but not forgotten
Posts: 218
|
posted December 18, 2011 02:58 PM
yes it was took about twenty minutes to change out arms, what I liked about they use brass inserts impregnated with oil you don't have to put in needle bearings or try to take yours out with damaging them andeverything fit really nice
____________
2012 ZX-14R SE
2002 VULCAN MEAN STREAK (11.41 @ 114 best 1/4)
I BLEED GREEN
|
Johnnycheese
Pro
Posts: 1008
|
posted December 18, 2011 03:10 PM
still no load control.
without it it is like spinning a 1000# wheel
if you don't think so take your numbers and run it I bet you never hit the mph that the hp says
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas
|
KAWITOM
Expert Class
My 12R gone but not forgotten
Posts: 218
|
posted December 18, 2011 03:25 PM
Johny not trying to argue because I am not an expert on dyno's so I don't even know how you there is no load control, I only have Glenn or Brian from WIN Racing base tune my bikes than I use my air fuel metering to optimize my tunes for condition of the day I'm running and save their maps for a baseline for the day or take different maps for similar weather conditions from previous outings. You sound like a knowledgable person so I am not going to doubt what you said.
____________
2012 ZX-14R SE
2002 VULCAN MEAN STREAK (11.41 @ 114 best 1/4)
I BLEED GREEN
|
kawa74
Expert Class
Posts: 226
|
posted December 19, 2011 05:12 AM
quote:
The room is bigger than it looks, it has been that way for seven or eight years alot of bikes have been on that dyno everything from pro street to regular streetbikes. He has lots of fans that you can't see in the room, yea it isn't room designed by dynojet, but he knows what he's doing, he's the tuner of the worlds fastest snowmobile, it's a custom chassis with turbo hayabusa motor in it with a chain drive setup and air shifter. Has gone 186 mph in 1000 ft. on ice, so I trust him
Where did he do this, Lake Michigan?? Wonder what the freaking wind chill was ?? How did he STOP on ice,? And how FAR did it take to Stop?? Half mile or more ?? That is INSANE, that takes HUMUNGUS NADS!!! Pro Stock Cars run around 190 mph @ 1000* . He"s running like about 5.60 et @ 1000* and about 6.80 @ 1/4 @ 208 mph on ICE , WOW
____________
"I have never met a man so Ignorant that I coun't Learn from him"..."Galileo"
|
Stu64
Zone Head
Posts: 548
|
posted December 19, 2011 10:28 AM
quote:
[URL=http://s1091.photobucket.com/albums/i399/kawitom/?action=view¤t=dyno004.mp4] [/URL]
Welcome to Hell's kitchen, my buddies building is big and part of it was an apartment, his dyno is setup in the old kitchen so the nickname fits LOL
Glenn Stickles? Had my bike on that dyno a few times,yeah the shop isn't fancy but he does good work and cheaper than most places.
|
Stu64
Zone Head
Posts: 548
|
posted December 20, 2011 05:09 AM
quote:
[URL=http://s1091.photobucket.com/albums/i399/kawitom/?action=view¤t=dyno004.mp4][/URL]
Welcome to Hell's kitchen, my buddies building is big and part of it was an apartment, his dyno is setup in the old kitchen so the nickname fits LOL
Glenn Stickles Place? Yeah its not the most organized shop,but he does a decent job and charges less than most dealers in my area.
|
Stu64
Zone Head
Posts: 548
|
posted December 20, 2011 05:11 AM
quote:
[URL=http://s1091.photobucket.com/albums/i399/kawitom/?action=view¤t=dyno004.mp4][/URL]
Welcome to Hell's kitchen, my buddies building is big and part of it was an apartment, his dyno is setup in the old kitchen so the nickname fits LOL
Glenn Stickles Place? Yeah its not the most organized shop,but he does a decent job and charges less than most dealers in my area.
|
|
|
HOME
NEW TOPIC