01smokes
Needs a job
Posts: 2243
|
posted May 08, 2011 08:59 PM
Can some one post a pic of the speedo nut that been ground
I'm away from a computer and searching off my phone and cant seam to find anything, and was wondering if some one can bump a thread with a pic or just post some pics up for me thanks guys
____________
PayPal, vigilart22@yahoo.com
Email, artvgl@yahoo.com
  
|
eklipse636
Needs a life
ZX-14
Posts: 6046
|
posted May 09, 2011 01:41 AM
It's the nut that holds your front sprocket on.
____________
Best: 60ft 1.351 1/8 5.68 mph 123.98 1/4
8.89 mph 151.32
|
ninjaboy311
Zone Head
Posts: 940
|
posted May 09, 2011 08:54 PM
____________
Naarden Speedlinks Sponsored Rider
Schnitz Racing Sponsored Rider
8.74 @ 152 on stock motor and MR9 (Muzzy Powered), 205 lbs suited
|
01smokes
Needs a job
Posts: 2243
|
posted May 09, 2011 09:20 PM
quote:
Thank you so much I appreciate it.
____________
PayPal, vigilart22@yahoo.com
Email, artvgl@yahoo.com
|
BlackMagic14
Needs a job
Posts: 2058
|
posted May 10, 2011 07:46 PM
Doesn't this affect the "miles" you put on your bike as well as your tach and in turn my autoshift?
|
CraigChrist
Pro
BAWLS
Posts: 1043
|
posted May 10, 2011 07:56 PM
It won't affect your shifts since your autoshift should be going off of your coil wire and not your speedo signal.
____________
60ft-------1.42
1/8th------5.97
mph-------119
|
ksig419
Novice Class
Posts: 42
|
posted May 10, 2011 10:24 PM
what does grinding one side off do? Is there a magnet on each of the four sides that the sensor picks up on and when you grind one off then it reads different?
|
Halvefast
Zone Head
Posts: 806
|
posted May 11, 2011 09:45 AM
the speedo pick-up reads each of the 4 corners,
remove 1 it reads 25% lower, remove 2 it reads 50% lower doesn't affect rpms at all
____________
Texas Mile 200.256mph - Oct. 2007 (Update 202.577mph Oct 2008) NOS assisted
ECTA Ohio Mile 195.132mph
TexasMile 2012 199.9 mph all motor!
Streetriders Shootout 2008 series Pro/ET Champ!
Streetriders Shootout 2007 Series Pro/ET Runner-up!
|
Sheard
Novice Class
Posts: 46
|
posted May 11, 2011 08:08 PM
Will this mess up the rpm on factory tach? Can I do this on stock bike?
|
ksig419
Novice Class
Posts: 42
|
posted May 11, 2011 10:32 PM
halvefast said that it would not affect RPM's at all so I assume yes
|
ninjaboy311
Zone Head
Posts: 940
|
posted May 14, 2011 11:26 AM
Does not affect RPM's. This is only the speedometer pick-up. Will slow down the mileage readings on the odometer, which is a good thing when its time to sell it.
____________
Naarden Speedlinks Sponsored Rider
Schnitz Racing Sponsored Rider
8.74 @ 152 on stock motor and MR9 (Muzzy Powered), 205 lbs suited
|
01smokes
Needs a job
Posts: 2243
|
posted May 14, 2011 01:10 PM
Just finished it works great.
____________
PayPal, vigilart22@yahoo.com
Email, artvgl@yahoo.com
|
ksig419
Novice Class
Posts: 42
|
posted May 14, 2011 02:20 PM
where is this nut located at?
|
01smokes
Needs a job
Posts: 2243
|
posted May 14, 2011 05:34 PM
My nuts are in my pants..
No its the sprocket nut.
____________
PayPal, vigilart22@yahoo.com
Email, artvgl@yahoo.com
|
3000psi and falling
Zone Head
Posts: 848
|
posted May 14, 2011 06:08 PM
HA!
____________
08 ZX14, 2010 Persimmon Red bodywork.
Flies pulled, 16-42, BMC street, 8" extensions, drag shock, cut pan, Cycle Concepts Drag Pack and springs, muzzy m14 w/ oval can, lowered, Shinco usoft rear, pcv with autotune, leightweight Shori 18ah battery, throttle meister. 500lbs at bandimeres scales with half tank of juice.
|
08green
Expert Class
Posts: 188
|
posted May 14, 2011 06:15 PM
lol
____________
2004 ZX10
2008 ZX14
|
eklipse636
Needs a life
ZX-14
Posts: 6046
|
posted May 14, 2011 06:48 PM
quote:
where is this nut located at?
Read post above. It's the nut that holds on the front sprocket.
____________
Best: 60ft 1.351 1/8 5.68 mph 123.98 1/4
8.89 mph 151.32
|
JSmooth
Expert Class
Posts: 169
|
posted May 15, 2011 06:58 AM
This may be a stupid question but here goes, has anyone shaved down all the corners on the nut? If so does it offer even better results? Yes I see where it was posted 1 corner and 2 corners but I want to know what is the effect of all 4 being done?
|
GREYHOUNDMOSES
Expert Class
Posts: 324
|
posted May 15, 2011 07:46 AM
Strictly speaking, this doesn't "de-restrict" the bike, it raises the speed at which the bike is restricted.
With two lobes removed the bike can go 372mph before the restrictor cuts in.
If you want to go faster than that you'll have to buy a V-Max.
They don't have any lobes on the sprocket nut. 
|
|
|
HOME
NEW TOPIC