runninhorn

Expert Class
Posts: 442
|
posted May 09, 2004 10:12 PM
Edited By: runninhorn on 9 May 2004 23:13
quote: Horn, I'm a goin to Chicago in the early morning, I'll catch up in the mid-evening. If I understood right, you need to split the LEDs into two groups, and treat each group like a single round light on the trailer - and whether or not the 'round light on the trailer' has one or two 'filiaments' you'll need to decide. Hope that makes sense.
have a safe trip, ill let you know what i find when you get back.....
|
runninhorn

Expert Class
Posts: 442
|
posted May 09, 2004 11:07 PM
well, its alot more technical than this, due to this being an LED turnlight that runs multiple LED's on a circuit board. Im gonna hold off until an aftermarket company comes out with a Integrator specifically for this bike, and its 2am, I gotta get to bed, ill probably mount the plate up under the bike tomorrow, and go get some LED's tomorrow as well to light the plate and see about mounting those two small amber LED's in the black voids and see how that looks.......
|
Erich
Expert Class
Posts: 131
|
posted May 09, 2004 11:12 PM
kz2zx hit upon the big difference. The stock tail light is essentually 1 light with its traces. Attempting to cut them and solder on, though doable(if you know how they are handling heat too), can also trash your light if you dont know exactly what you're doing.
If you are thinking the GSXR tail lights are comparable, they are in no way as they had seperate in candescent bulbs and wiring versus LEDs on a circuite board.
Your other option is to add leds to the existing light if there is room on the board, then wire them.
It'd be best to spend the money on the real deal. You will be happier and wont have wasted many hour of running back and forth to find it may not work anyway.
|
runninhorn

Expert Class
Posts: 442
|
posted May 10, 2004 12:08 AM
quote: kz2zx hit upon the big difference. The stock tail light is essentually 1 light with its traces. Attempting to cut them and solder on, though doable(if you know how they are handling heat too), can also trash your light if you dont know exactly what you're doing.
If you are thinking the GSXR tail lights are comparable, they are in no way as they had seperate in candescent bulbs and wiring versus LEDs on a circuite board.
Your other option is to add leds to the existing light if there is room on the board, then wire them.
It'd be best to spend the money on the real deal. You will be happier and wont have wasted many hour of running back and forth to find it may not work anyway.
My thoughts exactly, KZ was correct, and in a sense though wasnt posted here by myself, thats what I was trying to diagram out, attempting to make a "custom" circuit board, but it just isnt going to happen. Ill leave it as it is right now, will fab up something to install the license plate back up under there by the rear shock, and just not have any rear turn signals until a custom Integrator or some sort of Rear Integrator comes out for this bike, I dont want to GHETTOFY it, or make it look the least bit trashy.......
|
close2death
Novice Class
Posts: 69
|
posted May 11, 2004 05:50 AM
Save yourself all the trouble....wait a month and Clear Alternatives told me they'd have their intergrated tailight for $129.....I installed intergrator kits on my zx-9's before but have been told by many people the LED tailights are a royal pain in the ass and to go aftermarket....While $129 is a lil more than an intergator kit, if you try it yourself and screw it up Kawasaki will bend you over and rape you from the back for a replacement tailight anyways....this being said if anyone DOES try this themselves and has sucess let me know I'm always down for saving a buck.
|
|
|
|
|