HOME ARTICLES JOIN GALLERY STORE SPONSORS MARKETPLACE CONTACT US  
Register | FAQ | Search | Memberlist
Username:    Password:       Forgot your password?
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: no spark or fuel NEW TOPIC NEW POLL POST REPLY
Ra12r


Zone Head
Posts: 919
posted September 29, 2005 04:25 AM        
Alive, I wish I was close to you, because I would just come over and help you. You are in a learing mode and that is great, but you really need a tutor. It is hard to respond correctly, because there is a language barrier in you describing what you are touching and seeing?!

1) Your fast idle (choke) will correct itself when the vacume hoses are connected and a correct map is installed. That is unless you messed with the cable length???

2) Was the black mark on the head or the block? Make sure it was not a leaking exhaust gasket.

3) You just had your block done I thought?? I just can't believe it would be warped.......maybe though but unlikely unless you had the block surfaced??.

4) A bad PC3 will cause some white smoke also, but a different quality. However, the white smoke from a blown headgasket will be pretty constant during idle also. Different oil will burn with slight different colors. ANY HIGH PERFORMANCE MOTOR will smoke a litte at some times. This is NOT a problem, it is oil getting burned off from several different sources.

Email me your phone number.
____________
All must bow to the "Ra Supremecy"...

  Ignore this member   
johnnycheese


Pro
Posts: 1008
posted September 29, 2005 06:42 AM        
millieum does not surface your block after plating unless you as for it. that big bore on a stock block the walls are real thin even .002 off will cause a blown gasket without spray
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas

  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 29, 2005 07:00 AM        
Well,I just came from the machine shop and the cylinder surface isn't warped.
The black marks were on the cylinder in between cylinders.
The smoke was enough to block the view of the shack where they hand out time slips although no damage to the nicasil was noticed.No smoke at idle,only when motor was hot .The last time I had the block out,I only had it stripped,replated and then the cross hatch.
I haven't checked the head yet.I want to clean it all up and remove the bucket and shims and then I'll bring it down and have them check that for warpage.I was told they would do a valve job for $240,too bad I don't have the money for that.
I'm using the stock head bolts and wondered if perhaps they were stretching.
Trust me ,you guys are a great tutor.That distance thing maybe a blessing to keep me from stepping aside
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 29, 2005 04:58 PM        
cylinder on but still in need of a 87mm head gasket non-offset.anyone got one?
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
johnnycheese


Pro
Posts: 1008
posted September 30, 2005 05:22 AM        
I looked and didn't find but will check again
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas

  Ignore this member   
psycho1122


Pro
Posts: 1608
posted October 01, 2005 07:51 AM        
Call Cometic.....
____________
You say PSYCHO like it's a BAD thing!!

  Ignore this member   
All times are America/Va [ This thread is 3 pages long: 1  2  3   ] < Previous Thread     Next Thread >
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: no spark or fuel NEW TOPIC NEW POLL POST REPLY

FEATURED NEWS   Bikeland News RSS Feed

HEADLINES   Bikeland News RSS Feed


Copyright 2000-2026 Bikeland Media
Please refer to our terms of service for further information
0.53390192985535 seconds processing time