HOME ARTICLES JOIN GALLERY STORE SPONSORS MARKETPLACE CONTACT US  
Register | FAQ | Search | Memberlist
Username:    Password:       Forgot your password?
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: no spark or fuel NEW TOPIC NEW POLL POST REPLY
aliveagain


Needs a life
Posts: 5033
posted September 25, 2005 05:43 PM        
Ya know now that I'm thinking about it,the cheeseman said he had 2 head gaskets and I only got one.If anyone knows how to get ahold of him and see if he has another one some place,that would be great.I don't know how much he got rid of his business but its always a shot.
entropy smowing,is that like shoveling the lawn?
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
ninja12


Needs a job
Posts: 3310
posted September 25, 2005 07:53 PM        
Check the valcum hoses on the TB. Especially on the left side to the pressure sensor.
Switch the sensor with the one in the tail on the right.
Let us know what you find.

  Ignore this member   
entropy


Moderator
Posts: 8671
posted September 26, 2005 12:53 AM        
smowing?? hahahahahahahahaha.

It's still 100F here on the Mosquito Coast, no "smowing" necessary.

You have a SBM 87mm block (not offset??). I think JC did have 2 of those, not sure.
____________
This moderator uses moderation in moderation

  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 26, 2005 02:41 AM        
ninja12,I'm not following what you said about switch the sensor with the one in the tail on the right.
JC is checking.
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
Ra12r


Zone Head
Posts: 919
posted September 26, 2005 04:50 AM        
When I had my PC3 go bad it would run just like you are saying..........terrible smoke, then basically flooding the bike and shutting off.

I kinda feel like you have more than one problem. I currently don't feel you need to tear down your engine.

Problem
1) Alot of guessing about how motor systems work (makes it very hard to properly diagnose your observed symptoms)
2) Wrong fuel ratios for proper idling
3) A PC3 that is possibly going bad.

WHY??????? would you spray nitrous on a motor not running right?!?!?!?!?!?! Could you have created new problems......YES! (shaking head) "Your logic really confuses me dude."

I will send you my map. Good luck
____________
All must bow to the "Ra Supremecy"...

  Ignore this member   
entropy


Moderator
Posts: 8671
posted September 26, 2005 05:05 AM        
ra, a fukkered MAP sensor also makes it run like shit, eh?
(not that WE would ever mix up the TPS/MAP connectors... )
____________
This moderator uses moderation in moderation

  Ignore this member   
johnnycheese


Pro
Posts: 1008
posted September 26, 2005 05:42 AM        
quote:
ra, a fukkered MAP sensor also makes it run like shit, eh?
(not that WE would ever mix up the TPS/MAP connectors... )

smart ass
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas

  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 26, 2005 07:35 AM        
Ra,yes I'm a little whacked.I wanted to see if I was running that rich if the nitrous might clear it up.Never even felt it,but I only had 580lbs. on a 40 pill.
I'm real concerned as to why the white smoke,thats why I want to open up the motor.Last time I thought it was just a loose exhaust pipe and it turned out the nickosil had melted off.
In hind sight,It probably wasn't a good idea being that it would smoke grey/black at first and then white while putting around.I think it had been so longsince I ran it I just wanted to go for it.
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
dougmeyer


Needs a job
moderated
Posts: 2713
posted September 26, 2005 11:25 AM        
Load check the battery. If, under load, the voltage sags under about 12.8 V, everything goes to hell.
Doug

  Ignore this member   
entropy


Moderator
Posts: 8671
posted September 26, 2005 12:26 PM        
quote:
quote:
ra, a fukkered MAP sensor also makes it run like shit, eh?
(not that WE would ever mix up the TPS/MAP connectors... )

smart ass


bahahahahahahahahahaa
leastways I know what happens when you mix em up

That lil event was just another minichapter in my ongoing effort to break every mechanical and electrical component on that heap.

JC, you will be pleased to know that I somehow snapped the inlet pipe off the MAP sensor putting the motor back in the frame.

My Mom used to tell me: "Karl, you could fuk up a wet dream..."
____________
This moderator uses moderation in moderation

  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 26, 2005 06:15 PM        
I just pulled the fairing ,tank and radiator.The oil and pipes stink of gas.Tomorrow I'll drop the motor and pull the head for a peek.Only had 45 mins to work on it today but tomorrow,I'll have some time.
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
entropy


Moderator
Posts: 8671
posted September 26, 2005 11:09 PM        
I knew you couldn't wait for winter
(or... is it snowing already?????)
____________
This moderator uses moderation in moderation

  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 27, 2005 02:37 AM        
It dipped into the 40's once already,albeit,at night.Big momma is gonna want to get warm soon.
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
Ra12r


Zone Head
Posts: 919
posted September 27, 2005 04:00 AM        
Speaking of the battery, I just took mine for another test ride Sunday. While cruising along the bike just shuts off!!!! Battery DEAD.... Does the ECU have any codes for the alternator issues?
____________
All must bow to the "Ra Supremecy"...

  Ignore this member   
entropy


Moderator
Posts: 8671
posted September 27, 2005 04:32 AM        
put a voltmeter on the batt terminals, should read 13.5V?? or so when charging
____________
This moderator uses moderation in moderation

  Ignore this member   
ninja12


Needs a job
Posts: 3310
posted September 27, 2005 07:11 AM        
I'm talking about the sensor on the frame near TPS.
It has a wire connector and a valcum hose.
Runs like shit if that hose comes off or cracks.
Sometimes when people break the one near TPS
they swap it with the one on the right tail section of subframe.


  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 27, 2005 09:29 AM        
thanks ninja 12,I'll have to look there tonite after the motor is out.What should I look for as a clue that the gasket leaked water? Are there any telltale signs?Maybe I 'll check that sensor befor taking the motor off all the way.I like to pull the front engine mount and the rear upper mount,which allows me to pull the head and then its easier to carry.
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
ninja12


Needs a job
Posts: 3310
posted September 27, 2005 12:25 PM        
No need to pull engine to check that one.
It has the chrome 10 mm nut holding it to the frame.

  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 27, 2005 06:40 PM        
2 hrs.and the throttle bodies were off,engine dropped and head off.Found a hose off that went to that bell housing the fuel line attaches to.There was a plug on the spot where the tube goes,but the tube itself was not sealed,will reattach.Black marks between the cylinders.I'm not sure if I need to have the head and cylinders machined down or if this was a freak thing.I did use copper gasket spray on the gasket,not sure if this matters.Feeling good cause at least I know why the idle was off.I still have to fix the adjustment on the idle so the fast idle works.
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
entropy


Moderator
Posts: 8671
posted September 27, 2005 09:12 PM        
"Found a hose off that went to that bell housing the fuel line attaches to."

bell housing??? the fuel pressure regulator???

Personally, I would send the cyl block to milennium for checking & decking as needed. I believe that if the block is warped it needs to be put under a surface grinder (not an end mill) for decking. Something about the nikasil cyl coating.
____________
This moderator uses moderation in moderation

  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 28, 2005 06:46 AM        
Entropy,I'm not sure what it's called.It was just to the inside of the tps.I looked on Ron Ayers but could not find it on the fiche.Didn't know if it was a vacuum petcock.I guess that answers my question to ra on how it could be too lean.
Why does it have to go to milennium?Are you saying that I'll have to have it replated again?I was so close to saying fuck it and put on an old gasket for the month of Oct.
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
ninja12


Needs a job
Posts: 3310
posted September 28, 2005 07:11 AM        
Coat it and try it!
What do you have to loose?
After all It only your labor and a head gasket.
If it works you're riding, If not you wasted a few hour
of TV time.

  Ignore this member   
entropy


Moderator
Posts: 8671
posted September 28, 2005 07:20 AM        
If the block is warped you have to have it surface ground to get it flat.

If you think, hell it isn't warped THAT much, i'll just spend $80 on another hg... I think you'll be throwing $80 away

Do you know if it is warped???
____________
This moderator uses moderation in moderation

  Ignore this member   
aliveagain


Needs a life
Posts: 5033
posted September 28, 2005 11:17 AM        
I don't know if it is warped or not.Alls I know is that I was blowing white smoke after the run and that there was black soot between the cylinders.I was also told to check the cylinders for scalding,which can happen when the relatively cold water hits the hot lining
____________
I wondered why the baseball kept getting bigger. Then it hit me.

  Ignore this member   
entropy


Moderator
Posts: 8671
posted September 28, 2005 01:29 PM        
take it to a ggod automotive machine shop and have em test it (and the head) for flatness, but don't let them deck it with an end mill, it supposedly will chip the nikasil
____________
This moderator uses moderation in moderation

  Ignore this member   
All times are America/Va [ This thread is 3 pages long: 1  2  3     Next» ] < Previous Thread     Next Thread >
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: no spark or fuel NEW TOPIC NEW POLL POST REPLY

FEATURED NEWS   Bikeland News RSS Feed

HEADLINES   Bikeland News RSS Feed


Copyright 2000-2026 Bikeland Media
Please refer to our terms of service for further information
0.25754904747009 seconds processing time