HOME ARTICLES JOIN GALLERY STORE SPONSORS MARKETPLACE CONTACT US  
Register | FAQ | Search | Memberlist
Username:    Password:       Forgot your password?
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: ran 1270 on dyno.... NEW TOPIC NEW POLL POST REPLY
Hells Dark Lord


Needs a life
living life, and loving it.
Posts: 7981
posted May 03, 2004 03:41 AM        
amen BA

____________
When in doubt, lean farther and go faster....

  Ignore this member   
tpeterson


Parking Attendant
Posts: 2
posted May 03, 2004 04:28 PM        
Interesting Post. I had similar frustrations after Muzzy set me up for the fall. There claim of 190 HP from a 1270 is a pipe dream. I was pissed that I only got 175 HP after installing the 1270 kit with all the extras. Then I took it to the track and smoked all of the supposed "230" HP Busas with big bores, cams, and head work. Motor runs 9.0s @ 152 on motor and 8.8s on spray at 163 MPH. Not bad for a lead sled at 720 lbs with rider.
  Ignore this member   
johnnycheese


Pro
Posts: 1008
posted May 04, 2004 06:46 AM        
quote:
Richard, It really doesn't matter whether you buy it or not. You might consider reading the whole thread and the information on the factory pro website before calling bullshit. Factory Pro is claiming a 21-22% variation between true horspower and "Dynojet horsepower". That is where I got the number of 1.22 as a multiplier. The information on the website is there for you to read if you'd just take the time. From my perspective, I really don't care what the numbers are...relative to some dyno in Florida, or Hawaii or France or whereever. Until there is a universally accepted method of calculating horsepower and torque, there is no fair comparison. It's just a dick measuring contest anyways...dynojet is using a centimeter ruler and calling it an inch ruler to measure their dicks and then wowing all of us with the numbers of how well hung they are....until we all get to whip it out in public and see......

A dyno is a tool....not to measure horsepower for horsepower sake, but to measure horsepower to make changes and see if there is an improvement or not, as compared to the baseline run. I went to this shop to get a map made for my unusual combination.....and put down the strongest numbers they've ever seen. That number was 157.5 HP. I guess that means that those 180 HP power commander and pipe bikes are faster than my 1270, with porting, etc. I guess we'll just have to wait and see.


it is a 15% difference and I have found that unless the tuner knows what the hell they are doing you will be fucked on that dyno system trust me I am getting more work from that dyno in town due to the tuners suck
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas

  Ignore this member   
MadMike


Moderator
FEAR THE BLACK FLAG!!!!!!!!
Posts: 6579
posted May 04, 2004 07:13 AM        
quote:
My 1270 runs about 158-160mph in the 1/4 with me on it....Now, take off a few MPH if your a member of TFA




A few mph??? if your a true TFA member you better cut off 10mph! at least. man skinny girls rock but not when I'm racing them..... LOL..
____________
200-MPH CLUB MEMBER!

  Ignore this member    Click here to visit MadMike's homepage. 
zx12girl


Pro
Adrenaline Junkie
Posts: 1740
posted May 04, 2004 04:24 PM        Edited By: zx12girl on 4 May 2004 17:25
uuummm...Correction....158-160 is with the NOS button engaged....It has been a while since I have NOT hit the NOS button.

Only about 151-152 on the motor....I think that I saw 154 on a happy timer once....

Mike,
I am not that skinny...

  Ignore this member   
Hells Dark Lord


Needs a life
living life, and loving it.
Posts: 7981
posted May 04, 2004 04:29 PM        
you aint anywhere near mikes size there Angi
____________
When in doubt, lean farther and go faster....

  Ignore this member   
zx12girl


Pro
Adrenaline Junkie
Posts: 1740
posted May 04, 2004 04:35 PM        Edited By: zx12girl on 4 May 2004 17:47
quote:
you aint anywhere near mikes size there Angi


You are correct...They ripped up my entry form for Group TFA

  Ignore this member   
kcadby


Pro
Posts: 1733
posted May 04, 2004 05:39 PM        
I'm happy with the DynoJet Dyno I use to tune with...
a LOAD CONTROL dyno if used properly will get GOOOD results no matter what name is on it...

richard IS right about the 178 @ the Crank that Kaw puts on the paperwork that comes with the bikes...are they (Kaw) BSing "also"???

NOT here to debate dynoBRANDS though...

GLAD you and yer bike are HAPPY
Let us know what the ETs/MPHs are when you RUN IT!!!

  Ignore this member    Click here to visit kcadby's homepage. 
Hells Dark Lord


Needs a life
living life, and loving it.
Posts: 7981
posted May 05, 2004 01:57 PM        
lmfao@ Angi....dats a good thing right.....lmfao
____________
When in doubt, lean farther and go faster....

  Ignore this member   
frEEk


Administrator
ummm... yeah
Posts: 9660
posted May 05, 2004 03:45 PM        
sigh, here we go again, but it's a worthwhile topic so i'll say it again:

according to the writeup above (taken from the ec997 site), dynojet numbers estimate crack hp rather than rwhp. however, this doesnt entirely compute since the manufacturers' claimed crack numbers are significantly higher. so who is giving the "real" number here? and are DJ numbers actually supposed to be rw or crank or what? EC997's claimed numbers are very clear, and are said to be rw. assuming their description is true, this claim would appear to be accurate. (please note all the assumptions and "IF"s)

also, anyone reading thru the big writeup above, please note the difference between the steady-state and inertia modes. do not confuse them. they are measuring the output power of the bike (or car) under very different circumstances. actually, that brings up a possible explanation for the DJ readings... perhaps they are estimating not crank readings, but steady-state readings by estimating the power lost in accelerating the wheel and drivetrain? that would also explain the manufacturers seemingly high crank numbers: they could be steady-state numbers.

finally, recognize that regardless which numbers are bullshit and which arent (and i dont believe there is any such thing as bullshit numbers, jsut numbers measures and calculated differently), despite what some people claim, the standard numbers are DJ numbers. it may not be the industry standard (what engineers and regulators work with), but it is the standard in that all the magazines seem to report DJ numbers.

hmm... i think i have myself a mission!

  Ignore this member    Click here to visit frEEk's homepage. 
frEEk


Administrator
ummm... yeah
Posts: 9660
posted May 05, 2004 05:18 PM        
ok, i think i am really homing in on the accurate, clear answer this time. will take another day to get all teh info i need but i think i can finally put this damned issue to rest!
  Ignore this member    Click here to visit frEEk's homepage. 
Hells Dark Lord


Needs a life
living life, and loving it.
Posts: 7981
posted May 06, 2004 03:17 AM        
well???? Whats the answer freek, come on now we aint got all dam year to wiat.....lol
____________
When in doubt, lean farther and go faster....

  Ignore this member   
canadamaxxer


Pro
Posts: 1090
posted May 06, 2004 04:51 AM        
I suspect that at least part of the difference in the numbers is as a result of the correction factors that are used. Let me explain.....when Thunder Cycle ran my bike on their dyno, he did a step test from 4000 rpm to 11500 rpm in 1000 rpm increments. This meant that the bike would be held at that rpm by the dyno and have to sit at each RPM for 3 full seconds. The horsepower was measured at the end of each 3 second blast. This was compared to the sweep test, and the tech superimposed the step test data over the sweep. He then clicked and dragged the step test graph line up and down until it most closely matched the sweep test. At the side of this screen was a counter. In this counter was the number that was to be used as the correction factor for the rotating mass of MY tire, rim, chain, sprockets, etc. This number was used in the remainder of the days testing (the tech said that as long as the bike stayed on the dyno, that number was valid. If the bike was removed and then reinstalled, the correction process would have to be repeated to ensure that nothing had changed). From what I understand this is done to ensure that the playing field is equal....since a smaller, lighter tire on a lighter rim would have less inertia and would then be able to spin up faster than a heavier rim and tire, which I believe translates to higher HP numbers on an inertia dyno.

I have run several times on both Dynojet (150) and Superflo dynos and have never had the mass of the rim/tire taken into consideration. It seems to me that a small change in mass creates a large change in inertia and centrifugal force, and that change needs to be factored into the raw HP and torque data to be truely accurate. Once again, it may be that this is only true in of itself; in other words this may be only true for Factory Pro dynos, but it seems to me that accurate data for anything like this is absolutely needed.

  Ignore this member   
johnnycheese


Pro
Posts: 1008
posted May 06, 2004 06:12 AM        
This is why you do not use the Dj150 or the DJ 200, only the 250, and a GOOD TUNER knows how to use it.

But I said it again GOOD TUNER after all the dyno is a tool and there are alot of knobs who have one
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas

  Ignore this member   
frEEk


Administrator
ummm... yeah
Posts: 9660
posted May 06, 2004 12:12 PM        
well, i thought there was more new info to be had, but after reading through my old thread on dynos, i see i pretty much had it right back then, with jsut a few related points missing. have updated that thread with what i think are my final conclusions.

/board/viewthread.php?FID=1&TID=8536

  Ignore this member    Click here to visit frEEk's homepage. 
johnnycheese


Pro
Posts: 1008
posted May 06, 2004 01:11 PM        
Freek it boils down to a dyno is a tool PERIOD !!!!!
If you start and finish on the same dyno that work is being done one you will see the gains or losses.
This is why I dyno every bike before I do performance mods this way I know if I helped or hurt it.
if the customer goes to another shop and it makes more or less I could not care. if it came back to my shop and made less then I know I have a problem.
Plus with all the controlled room dynos they will always read higher than mine in an open air shop
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas

  Ignore this member   
entropy


Moderator
Posts: 8671
posted May 06, 2004 02:57 PM        
quote:
... all the controlled room dynos they will always read higher than mine in an open air shop


bada bing!!!!! we have a winner!!!
____________
This moderator uses moderation in moderation

  Ignore this member   
canadamaxxer


Pro
Posts: 1090
posted June 05, 2004 09:34 PM        
I took my baby to a Dynojet tuning centre today. He ran it four times with a maximum horsepower of 210.3 HP at 9522 RPM (No lie...I can post a scan of the printout......I am shocked too!!!!). It would appear that the reduction porting works!! Now I am really confused. Which is correct...the Factory Pro or the Dynojet. The industry standard is Dynojet, so I guess I made 210+HP. I know the things really hauls ass.....but 210HP worth of hauling ass?
  Ignore this member   
Hells Dark Lord


Needs a life
living life, and loving it.
Posts: 7981
posted June 06, 2004 03:30 AM        
cool beans Maxxer.....that is really good HP for a 1270 kit......but what is she running in the 1/4th mile?

____________
When in doubt, lean farther and go faster....

  Ignore this member   
Y2KZX12R


Needs a job
CompetitionCNC.com
Posts: 3762
posted June 06, 2004 05:39 AM        
Hey Canada... can you elaborate a bit on the porting. Thanks.
____________
Y2KZX12R
CompetitionCNC.com

  Ignore this member    Click here to visit Y2KZX12R's homepage. 
Ra12r


Zone Head
Posts: 919
posted June 06, 2004 06:25 AM        
JC, that is my mindset too,,,,a tool to determine if changes improved or hurt the performance. The let MPH be the braging number not HP. I no longer think HP, I think MPH.

Entropy got 159 MPH!!! Man that gives me HOPE!!!!!!!!!!!!!! His setup to me is the most occomplished on this website, as it is ALL MOTOR. This is the information that helps every bike. NOS is a shortcut, without improving the airpump. Turbo is a shortcut without improving the airpump. Entropy has improved his airpump quite a bit.
____________
All must bow to the "Ra Supremecy"...

  Ignore this member   
canadamaxxer


Pro
Posts: 1090
posted June 06, 2004 06:45 AM        
I haven't had a chance to run it on the 1/4 mile. I have played with it on the street and it stands up on it's back wheel far too much. If you think of the videos of the turbo Busa pointing it's nose in the air everytime the throttle is twisted...mine is like that at WOT above 7000 RPM. It is a wild ride, but not controllable on the track. I have some swingarm extenders that are going on the bike right away, and I'm hoping that 7" of wheelbase and lowering will help.

Y2KZX12R: The reduction porting is the method done by Pat at mototuneusa.com. I filled the port floor with JB weld and sanded and blended until the port height was 65% of the intake valve diameter. I also port matched the intake rubbers.

  Ignore this member   
johnnycheese


Pro
Posts: 1008
posted June 06, 2004 07:44 AM        
quote:
JC, that is my mindset too,,,,a tool to determine if changes improved or hurt the performance. The let MPH be the braging number not HP. I no longer think HP, I think MPH.

Entropy got 159 MPH!!! Man that gives me HOPE!!!!!!!!!!!!!! His setup to me is the most occomplished on this website, as it is ALL MOTOR. This is the information that helps every bike. NOS is a shortcut, without improving the airpump. Turbo is a shortcut without improving the airpump. Entropy has improved his airpump quite a bit.

the 12 That I was doing my testing on was the same one I talked about earlier in this post. removing the s pipe and can gave it 182 hp.
But with the A/F @ 12.1:1 it did not make ponies but it did make a 300# man go 138 in the 1/4.


canadamaxxer
The best thing to do is use uncorrected and the usewhatweather you have right then and correct yourself.
The Fatory Pro will not give you SAE (i do not know about uncorrected) but apples to apples
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas

  Ignore this member   
canadamaxxer


Pro
Posts: 1090
posted June 06, 2004 07:57 AM        
JC,

What is typical to see on a dyno printout from a DJ dyno? I only have the printout to go by. There is no atmospheric info on the sheet (no temp, humidity, baro pressure, etc). I also don't have an a/f printout even though I asked for one (which is a bit of a piss off). I have no idea if the run was corrected or uncorrected, and have no idea what correction factors to use based on atmospheric conditions, etc. The more I think about it, the more I am unimpressed. This is the whole reason why I drove 4 hours to find a professional shop to tune the bike originally.....I work in a professional shop (automotive) and expect that level of professionalism in a bike shop as well.

  Ignore this member   
frEEk


Administrator
ummm... yeah
Posts: 9660
posted June 06, 2004 11:41 AM        
just give the shop a call & ask them what correction factor their dyno is setup with. i imagine they don't change it.
  Ignore this member    Click here to visit frEEk's homepage. 
All times are America/Va [ This thread is 3 pages long: 1  2  3     Next» ] < Previous Thread     Next Thread >
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: ran 1270 on dyno.... NEW TOPIC NEW POLL POST REPLY

FEATURED NEWS   Bikeland News RSS Feed

HEADLINES   Bikeland News RSS Feed


Copyright 2000-2026 Bikeland Media
Please refer to our terms of service for further information
0.29455590248108 seconds processing time