HOME ARTICLES JOIN GALLERY STORE SPONSORS MARKETPLACE CONTACT US  
Register | FAQ | Search | Memberlist
Username:    Password:       Forgot your password?
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: Rod Bearings ?? NEW TOPIC NEW POLL POST REPLY
MadMike


Moderator
FEAR THE BLACK FLAG!!!!!!!!
Posts: 6579
posted April 12, 2004 04:10 AM        
have you guys called Tony at MTC and asked him about it? He might have seen something like this before? also with the billet stroker. is the wrist pin angle to severe. like the piston to rod connection? just an idea.
____________
200-MPH CLUB MEMBER!

  Ignore this member    Click here to visit MadMike's homepage. 
Johnnycheese


Pro
Posts: 1008
posted April 12, 2004 06:52 AM        
Mike Tony has the pistons in his hands. Had them for about a week now.
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas

  Ignore this member   
psycho1122


Pro
Posts: 1608
posted April 12, 2004 06:57 AM        
entropy;

Could this be a result of the Detonation the engine suffered?? The heat buildup and forces "could" hurt pistons (forged) in a variety of way's!
____________
You say PSYCHO like it's a BAD thing!!

  Ignore this member   
entropy


Moderator
Posts: 8671
posted April 12, 2004 07:34 AM        
psycho,
the pistons & plugs show no evidence of detonation. I was using very trick race gas (VP-C44), and only have 14.2:1 compression.

fukken mystery, eh?
____________
This moderator uses moderation in moderation

  Ignore this member   
fearless


Novice Class
Posts: 66
posted April 12, 2004 07:48 AM        
Help to answer a question of mine since it has not been metioned, I'm a friend of TN1361 and have wittnessed many Dyno runs on this particular bike and in my opinon well over 200 Dyno runs in 4000 miles and repeated trips to The Maxton Mile is one of the contributing factors in the distruction of the bearings! (Redline+Heat=Meltdown)
  Ignore this member   
Ra12r


Zone Head
Posts: 919
posted April 12, 2004 11:06 AM        
Entropy, make sure you check your bearings and have the rods checked in the reciprocating end to make sure they are still in round. Dang I hate this for you!
____________
All must bow to the "Ra Supremecy"...

  Ignore this member   
Johnnycheese


Pro
Posts: 1008
posted April 12, 2004 11:48 AM        
They are all brand new but will check tomorrow
____________
Builder and tuner of some of the fastest N.A. and P/A Hayabusas and ZX12 /14 in Texas

  Ignore this member   
VincentHill


Needs a life
Posts: 6520
posted April 12, 2004 01:06 PM        
Looking over this post, TN, did you ever remove the Oil Pan and clean the screen for the Oil PicK up? A lot of Clutch slipping will fill the screen and cause Oil Starvation and serious 60 foot times can starve the oil pump without an Accumulator!
____________
Made History @ Daytona and still one fast old man!!

  Ignore this member   
tn1361


Novice Class
Posts: 43
posted April 12, 2004 02:30 PM        
Psycho : Not sure what caused the #2 rod bearing failure yet

Madmike : Always ran the bike with 2.8 liters of oil. Ran it for a short
period of time with zero weight oil. Just a few dyno pulls and
about 10 times down the Maxton mile. Maybe this might have
started my problems ?

entropy: I am using JE pistons. These were the pistons that came with
the Muzzy kit.

Vincent : Never cleaned the pick up screen. This is only my second clutch
in the bike. The new one still looks brand new. Removed the
oil pick up and looked at the screen. Had some crud in it but not
enough to be alarmed about.

Wonder if anyone has had this trouble with a stock motor. Maybe the angle is too sevier with a stroker kit.

  Ignore this member   
VincentHill


Needs a life
Posts: 6520
posted April 12, 2004 03:08 PM        
Tn, I think the thing that really puzzles most of us specially me is that it is #3 Rod Bearing that is usually spun first! Someone here had a problem but it was related to the difference between 00/01 Cranks and 02/03 cranks or something like that. I am down to the using of Kerosene ("0" W Oil!) There is just "Nothing" to keep the parts apart!

Hear this Dan?
____________
Made History @ Daytona and still one fast old man!!

  Ignore this member   
oldkawboy


Needs a job
Posts: 2125
posted April 12, 2004 04:38 PM        
Vincent....Man you got a good memory!! :-)

I really wanted to break that 200mph mark and I honestly believe by using the light weight fully synthetic oil(kerosene) helped me out with no more mods than I had. We made over twenty passes that day and I have since put over 10,000 miles on the bike with one more trip to Maxton (with gear oil last time) and numerous passes at the strip and it's still together. Come to think of it, I only ran 196 the last time....Musta been the oil!!!!!!
I know that 0w/10 is kinda foolish, but I was hungry and I'm glad it worked out for me. BTW, never use that stuff on the sreet 'cause idling will kill it.
When we going back Vince??

Tim,
I believe the last meet at Maxton your bike had the 5w/40 Motul 300v. We may have had the 5w/30 back in the Spring.
Dan

  Ignore this member   
krexken


Zone Head
Posts: 732
posted April 13, 2004 07:34 AM        
I haven't done the math as far as rod length/stroke ratio but I'm thinking that shouldn't be a problem. Most bikes have waaay better ratios than car engines. The main drawback of a short rod/long stroke motor is side loading of the pistons against the cyclinder walls. Don't think it would affect the pins.

Yall sure you have adequate piston to head clearance? Remember that the pistons do rock in the bores somewhat. Evidence shoud be easy to spot.

Fearless, I agree with you. You run a hotrodded engine this hard and something eventually will give. It's just the nature of an engine. They never live forever, unfortunately.

  Ignore this member   
FASTONE


Parking Attendant
Posts: 5
posted July 11, 2004 08:09 PM        
I lost my con rod bearings on #2 and#3 service guy said the pickup tube is short on the 02 12 so keep oil level at top of sightglass. Also long wheel stands is hard on the bottom end.
  Ignore this member   
All times are America/Va [ This thread is 2 pages long: 1  2   ] < Previous Thread     Next Thread >
BIKELAND > FORUMS > ZX12R ZONE.com > Thread: Rod Bearings ?? NEW TOPIC NEW POLL POST REPLY

FEATURED NEWS   Bikeland News RSS Feed

HEADLINES   Bikeland News RSS Feed


Copyright 2000-2026 Bikeland Media
Please refer to our terms of service for further information
0.41226601600647 seconds processing time