LAB3
Needs a job
Posts: 2977
|
posted April 06, 2011 06:07 PM
Paint combo looks Great.
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 06, 2011 06:13 PM
quote: Paint combo looks Great.
Thanks. These are the number plates that I will be adding- one on the nose under the screen
and two on the tail section
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 08, 2011 05:16 PM
The replacement R-R subframe is on the bike
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 08, 2011 05:20 PM
Yet again I will leave the mess of cables under the seat unorganized
and also heavily rely on zip-ties- this is the tip-over sensor on the very tail of the sub
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 08, 2011 05:23 PM
And with the new seat... this thing is blue...
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 12, 2011 06:56 PM
My GPR dampers are back- replaced oil, gaskets and bolts.
$25 for service for each and shipping cost to and from the manufacturer.
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 12, 2011 07:02 PM
These bushings I inconveniently overlooked when replacing my rear shock.
They fit inside of the top clevis and don't allow free play (sway) with the Penske unit
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 18, 2011 06:42 PM
My number plates from Drippinwet arrived, hope I don't get them all crooked on the bike
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 21, 2011 07:03 PM
Edited By: masszx14 on 22 Apr 2011 03:04
I'll need a functioning rear brake in order to pass tech inspection at the track.
Didn't buy a gsxr1000 caliper with pads, so I got a set of sintered Galfers
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 27, 2011 02:21 PM
I have a few spy shots of the built.... the bike is being tested at an undisclosed location....
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 27, 2011 02:28 PM
Well, the bike surely needs a few things addressed before going to the track but I hope I have time to wrench on it some more this week.
If I can get my suspension geometry dialed in and dyno tune some time next week I'll be only a few weeks behind schedule...
____________
universal@mind
|
LAB3
Needs a job
Posts: 2977
|
posted April 27, 2011 02:34 PM
Looks Great Stan. Almost too nice to risk a oppps in a tight turn. :-)
Louis
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 27, 2011 02:46 PM
Track bikes look nice and shiny only in the beginning of the season...
After that it's mostly back to unpainted bodywork in primer and lots more zip ties and rough spare parts.
This bike has been down more times than a truck stop hooker, crashes don't worry me much.
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted April 27, 2011 03:37 PM
Here's a few more...
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted June 20, 2011 05:06 PM
I've just been riding the damn thing, no spills this season yet.
Some pics from NJMP Lightning and NJMP Thunderbolt tracks
Her R1
And a little sequence of a clean pass after the S's at Thunderbolt:
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted September 18, 2011 06:41 AM
Being a long time Pirelli faithful, I've switched to Dunlops and couldn't be happier.
The NTecs just beg to be ridden hard and the bike geometry seems to be easier to dial up for the different tracks
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted September 18, 2011 06:46 AM
After struggling to figure out why my Woodcraft stator cover just kept leaking oil after replacing the gasket numerous times, I've switched back to the oem cover
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted September 18, 2011 06:51 AM
And I've just been getting seat time on the 750, although I've added a new bike to the stable
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted September 19, 2011 05:31 PM
Here's the MotoMounts GoPro mount that I use
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted September 19, 2011 05:35 PM
And an action shot from NHMS
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted January 05, 2012 11:17 AM
I have plans for the 2012 season, this thread will be revived asap!
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted January 07, 2012 03:53 PM
These are the wheels that the 750 will roll on this season, the beautiful and lightest BSTs
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted January 07, 2012 03:59 PM
I've decided to give the newer Vesrah Super RJL 17 pads a shot, many rave about them.
Again, the 750 has Yamaha R1/R6 monoblock calipers
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted January 28, 2012 05:38 PM
Picked up a set of forks with an Ohlins 20 mm kit and a set of Traxxion 20 mm fork extender caps
____________
universal@mind
|
masszx14
Pro
A mind beside itself!
Posts: 1806
|
posted January 28, 2012 05:41 PM
Promised myself not to get carried away with titanium hardware but couldn't resist some ti brake rotor bolts
____________
universal@mind
|
|