HOME ARTICLES JOIN GALLERY STORE SPONSORS MARKETPLACE CONTACT US  
Register | FAQ | Search | Memberlist
Username:    Password:       Forgot your password?
BIKELAND > FORUMS > ZX-14.com > Thread: Hays clutch NEW TOPIC NEW POLL POST REPLY
zx13r


Expert Class
Capt-America
Posts: 181
posted May 16, 2012 04:29 AM        
Hays clutch

Anybody put a hays on a 2012 yet?
I know I'm going to have to make a spacer for the inner hub
(from on 08) not sure if the basket is the same yet...
Should have more info next week.
____________
Sposored By:
Kawasaki Sports Center
ShoTime Graphics.com

  Ignore this member   
dakota9498


Pro
Posts: 1179
posted May 16, 2012 06:00 AM        
That will probably be a negative. A guy over on Psychobike is building a new 14R and pulled the clutch basket out and compared it to an 08-11 and they are different. The gears are also different along with a couple of other things.

Scroll to almost the bottom of the page and he has pictures comparing the two.

http://www.psychobike.com/forums/kawasaki-zx12r-zx14/95341-2012-14-boost-3.html
____________
2008 ZX14
Never argue with a fool, onlookers may not be able to tell the difference. ~Mark Twain


  Ignore this member   
1badzx12r


Needs a life
Posts: 8321
posted May 16, 2012 06:12 AM        
quote:


http://www.psychobike.com/forums/kawasaki-zx12r-zx14/95341-2012-14-boost-3.html



i don't know what to think on that CP piston ..i'm gonna wait until i hear more info on how they work out ..
____________
http://www.youtube.com/watch?v=S06nIz4scvI

  Ignore this member   
BrucerZX14


Expert Class
Posts: 365
posted May 17, 2012 01:24 PM        Edited By: BrucerZX14 on 17 May 2012 21:25
My buddy ands I tried to install his Hayes clutch from an '08 into his 2012. No go. The splined output shaft on the 2012 is about 1/2 inch longer. The ring gear was fine. The hub isn't. Hayes is gonna have to rework their set up for a 2012 ZX14.
  Ignore this member   
zx13r


Expert Class
Capt-America
Posts: 181
posted May 18, 2012 06:44 PM        
As long as the basket was the same,
you can make a spacer for the old inner hub,
I'm thinking. Hopefully next week I'll have a little time
to play with it.

____________
Sposored By:
Kawasaki Sports Center
ShoTime Graphics.com

  Ignore this member   
kawasakijockey


Pro
Posts: 1876
posted May 18, 2012 07:19 PM        
MTC has no immediate plans for any clutches either. They are not even currently designing one of any kind(single, multi, or gen2).
____________
Get on the shortbus boys 'cause its time to get schooled.
2007 ZX-14
1.38 60ft
9.03 @ 149mph
8.95 @153 small shot n2o
8.68 @160mph 5lbs boost

  Ignore this member   
zx13r


Expert Class
Capt-America
Posts: 181
posted May 18, 2012 07:28 PM        
When I talked to Tim he said the spacer would be the best bet....
It's the same size as the rear axel. I bought a brake remover/spacer that i never used, I'm going to mill it down and try that.
____________
Sposored By:
Kawasaki Sports Center
ShoTime Graphics.com

  Ignore this member   
Audio


Expert Class
Posts: 117
posted May 25, 2012 10:04 PM        
I put my 08 basket in my 2012 (its the same for sure, even has the same kawasaki part number ) there is about a 1/2 inch gap on the shaft, but also the front cover also liked about a 1/2 inch from being able to bolt up to the basket. So I'm not sure what to do about that.
____________
Audio
2008 ZX14 Old Gray CNC-1414 old new CNC ?
2012 ZX14R SE Green CNC-?

  Ignore this member   
All times are America/Va < Previous Thread     Next Thread >
Quick Reply:

Email Notification: Send all replies to your email address.
BIKELAND > FORUMS > ZX-14.com > Thread: Hays clutch NEW TOPIC NEW POLL POST REPLY

FEATURED NEWS   Bikeland News RSS Feed

HEADLINES   Bikeland News RSS Feed


Copyright 2000-2014 Bikeland Media
Please refer to our terms of service for further information
0.20860004425049 seconds processing time