HOME ARTICLES JOIN GALLERY STORE SPONSORS MARKETPLACE CONTACT US  
Register | FAQ | Search | Memberlist
Username:    Password:       Forgot your password?
BIKELAND > FORUMS > ZX-14.com > Thread: PCV for 14R? Fairy Tale or Real??? NEW TOPIC NEW POLL POST REPLY
Lucky14


Pro
Posts: 1439
posted April 05, 2012 03:57 PM        
PCV for 14R? Fairy Tale or Real???


Next week is finally here!!!









____________
You only need two tools: WD-40 and Duct Tape.
If it doesn't move and should, use the WD-40.
If it shouldn't move and does, use the duct tape.

  Ignore this member   
Wheelie


Needs a life
Old Man
Posts: 6902
posted April 05, 2012 03:58 PM        
see you at the track




































next week.

wee

  Ignore this member   
smokinZX14


Needs a life
Posts: 10197
posted April 05, 2012 04:04 PM        
Got mine also ...It came to late to make it to the track tonight ...UPS sucks ...
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95

  Ignore this member   
Lucky14


Pro
Posts: 1439
posted April 05, 2012 04:26 PM        
quote:
see you at the track



next week.

wee


That's a bit optimistic, don't you think?


quote:
Got mine also ...It came to late to make it to the track tonight ...UPS sucks ...


Yeah, mine got here about 6:30.
It was on the truck for 12 hours riding all over the Dallas area, I guess ...........


____________
You only need two tools: WD-40 and Duct Tape.
If it doesn't move and should, use the WD-40.
If it shouldn't move and does, use the duct tape.

  Ignore this member   
smokinZX14


Needs a life
Posts: 10197
posted April 05, 2012 07:19 PM        
It was an easy install ... And i liked the fact that the ground wire now goes to the main frame ground unlike the Gen 1 set up .. Two plugs that snap right in and one easy tap in the gear sensor line ..
____________
Smokin Performance Cycles..
Tampa Bay , FL .. Brocks Performance Dealer ..
Gen 2 ZX14R Best ET 8.43 , Best MPH 164.95

  Ignore this member   
mma-tv


Expert Class
Posts: 147
posted April 05, 2012 08:27 PM        
I suppose I'll go on ahead and order one....


Next week.

  Ignore this member   
pazx14rider


Zone Head
Posts: 953
posted April 06, 2012 03:28 AM        
On my 07 i put it under the seat (also had a tiger tail) on my 2012 i put it beside the left ram air tube. Is that where eveyone else is putting them or have you manged to put them somewhere else with the stock undertail?

  Ignore this member   
Lucky14


Pro
Posts: 1439
posted April 06, 2012 03:46 PM        
quote:
It was an easy install ... And i liked the fact that the ground wire now goes to the main frame ground unlike the Gen 1 set up .. Two plugs that snap right in and one easy tap in the gear sensor line ..


Well, mine is installed.
Only took me 24 hours - that's pretty good for me.................

Easy? Define "easy"?
Other than the backs of my hands look like a Rott has been chewing on them, not horrible.

pazx14rider, I put mine by the left ram air tube.


____________
You only need two tools: WD-40 and Duct Tape.
If it doesn't move and should, use the WD-40.
If it shouldn't move and does, use the duct tape.

  Ignore this member   
All times are America/Va < Previous Thread     Next Thread >
BIKELAND > FORUMS > ZX-14.com > Thread: PCV for 14R? Fairy Tale or Real??? NEW TOPIC NEW POLL POST REPLY

FEATURED NEWS   Bikeland News RSS Feed

HEADLINES   Bikeland News RSS Feed


Copyright 2000-2023 Bikeland Media
Please refer to our terms of service for further information
0.20794892311096 seconds processing time